CCNA ICND2 lab11 – EIGRP Routing Protocol

Ensurepass EIGRP Routing Protocol A: Lab Tips: Enhanced Interior Gateway Routing Protocol (EIGRP) is a proprietary Cisco IP routing protocol. Lab Requirements: 1. Perform basic routing configurations. 2. Use loopback interfaces to replace PCs. Topology: Lab Process: P4S1(config)#interface serial1/1 P4S1(config-if)#ip address 172.16.1.1 255.255.255.0 P4S1(config-if)#no shutdown P4S1(config)#interface loopback 0 P4S1(config-if)#ip add 192.168.1.1 255.255.255.0 P4S1(config)#interface loopback Read more […] Read more »

CCNA ICND2 Lab15 – Access List

Ensurepass Lab Tips: The ACL is a security solution that filters packets when they pass through a router. ACLs are divided into standard ACLs and extended ACLs. To pass the CCNA exam, please note the ip access-list command. Topology: Lab Requirements: Standard ACL P4S-R1 filters packets from P4S-R2. P4S-R1 configuration: 1. Create an ACL access-list 10 deny host 10.1.1.2 access-list 10 permit any 2. Apply the ACL to the interface Interface serial 1/1 Ip access-group 10 in P4S-R1 and P4S-R2 Read more […] Read more »

CCNA ICND2 Lab 4 – Revert Router Password

Ensurepass Lab Topology: Lab Requirements: 1. The router name is ciscobible. The console port of the router is connected to the com port of the PC through a reverse cable. 2. Set the password of the router to ccna and save the settings. 3. Restart the router and decrypt the password. Lab Process: Configurations on the router Router(config)#hostname ciscobible Ciscobible(config)#enable secret ccna Ciscobible(config)#exit Ciscobible#copy running-config startup-config Ciscobible#reload When restarting Read more […] Read more »

CCNA ICND2 Lab 6 – Create and Use Loopback Interface

Ensurepass Lab Topology: Lab Requirements: 1. The router names are P4S1 and P4S2. 2. Create a loopback interface on either of the routers and specify an IP address to every loopback interface. 3. Delete the loopback interfaces. Lab Process: 1. The loopback interface is a logical virtual interface on the router. A router has no loopback interfaces by default, but they can be created on it. In normal cases, a router has fewer interfaces than a switch; therefore, you need to create loopback interfaces Read more […] Read more »

CCNA ICND2 Lab12 – PAP Authentication

Ensurepass Lab Tips: PPP supports device authentication through the two following protocols: PPP Authentication Protocol (PAP) and Challenge Handshake Authentication Protocol (CHAP). PAP is easier but not safe. Through two handshakes, the sender sends the user name and password in clear text to the receiver. The receiver compares the user name and password in the received packet and those it stores. If they are the same, the receiver sends a message to permit. If not, the receiver sends a message Read more […] Read more »

CCNA ICND2 Lab2 – Set Router Port Address/Label and Save Settings

Ensurepass Lab Topology: Lab Requirements: 1. On the router port, set the IP address to 202.119.249.219 and mask to 255.255.255.0. 2. Set the router prompt message to welcome to router CCNAlab. 3 Set the router port prompt message to this is a serial port 4. Save the settings. Lab Process: Router>enable Router#configure terminal Router(config)#interface fastethernet 0/0 Router(config-if)#ip address 202.119.249.219 255.255.255.0     / set the IP address of fast Ethernet port Read more […] Read more »

CCNA ICND2 Lab 3 – CDP Command Operations

Ensurepass Lab Topology: Lab Requirements: 1. Router name: P4S1, P4S2, P4S3 2. Set password to cisco, secret to cisco1, and vty to cisco. All the passwords are required to be encrypted. 3. Configure all these routers. Lab Process: Configure Router 1. Router>enable Router#configure terminal Router(config)#hostname P4S1        / set router name P4S1(config)#enable password cisco             / set Read more […] Read more »

CCNA ICND2 Lab 5 – Configure Telnet Remote Access

Ensurepass Lab Topology: Lab Requirements: 1. The router names are P4S1 and P4S2. 2. Set the privilege password and the vty line password on P4S2. 3. Telnet from P4S1 to P4S2. 4. View other users that telneted to P4S2. Lab Process: The configurations of P4S2 are as follows: P4S2(config)#enable secret cisco            / set enable password P4S2(config)#line vty 0 4                   Read more […] Read more »

CCNA ICND2 Lab 10 – Configure OSPF Protocol in a Single Area

Ensurepass Lab Topology: Lab Requirements: 1. The router names are P4S1, P4S2 and P4S3. 2. Three routers are located in one area. 3. Connect the three routers and enable the OSPF routing protocol on the router. Lab Process: 1. As shown in the topology, configure the IP addresses of the router interfaces. Run the no shutdown command to activate the interface. 2. Run the clock rate 64000 command to configure the clock rate on S1/1 and S1/2 of P4S2. 3. Run the ping 3.3.3.3 command on P4S1 to Read more […] Read more »

CCNA ICND2 Lab 7 – Configure Static Route and Default Route

Ensurepass Lab Topology: Lab Requirements: 1. The router names are P4S1, P4S2 and P4S3. 2. Configure default routes on P4S1 and P4S3. 3. Configure a static route on P4S2. Lab Process: 1. Configure P4S1 Router>enable Router#configure terminal Router(config)#hostname P4S1 P4S1(config)#interface s1/1 P4S1(config-if)#ip add 192.168.12.1 255.255.255.0 P4S1(config-if)#no shut P4S1(config-if)#interface loopback 0 P4S1(config-if)#ip add 1.1.1.1 255.255.255.0 2. Configure P4S2 Router>enable Read more […] Read more »

CCNA Routing&Switching Lab Kits

Ensurepass ICND1 Labs CCNA ICND1 Lab1 – Basic Switch Command (1) CCNA ICND1 Lab1 – Basic Switch Command (2) CCNA ICND1 Lab2 – Restore Switch Password CCNA ICND1 Lab3 – Routing Between VLANs CCNA ICND1 Lab4 – Configure VTP CCNA ICND1 Lab5 – PAT Application CCNA ICND1 Lab6 – Configuring Dynamic NAT CCNA ICND1 Lab7 – DHCP Application CCNA ICND1 Lab8 – Configuration of RIPv2 CCNA ICND1 Lab9 – Layer 3 Switch and Proxy Server CCNA ICND1 Lab10 – Configuration Read more […] Read more »

CCNA ICND2 Lab 8 – Configure RIP Dynamic Route

Ensurepass Lab Topology:   Lab Requirements: 1. The router names are P4S1 and P4S2. 2. The loopback interface of P4S1 is loopback0 and the loopback interface of P4S2 is loopback0. 3. The S1/1 interface of P4S1 is the DCE end. 4. Start the RIP routing protocol on both routers. 5. View the routing table on the router and run the ping command to test connectivity. Lab Process: 1. As shown in the topology, configure IP addresses for both router interfaces. Run the no shutdown command to activate Read more […] Read more »

CCNA ICND2 Lab 9 – Use Extended ACL to Block ping Command

Ensurepass Lab Topology: Lab Requirements: 1. The router names are P4S1 and P4S2. 2. The S1/1 interface of P4S1 is connected to that of P4S2. The S1/1 interface of P4S2 is the DCE end. 3. Use the ping command on P4S1 to test the connectivity to P4S2 and access P4S2 from Telnet. Lab Process: 1. Configure enable password and VTY password on P4S2. Both passwords are ciscobible. 2. Perform basic configurations on both routers. 2.1 Configure P4S1: P4S1(config)#int s1/1 P4S1(config-if)#ip add Read more […] Read more »

CCNA ICND2 Lab 1 – Change Router Name and Password

Ensurepass Lab Topology: Lab Requirements: 1. Router name: router 2. Set password to cisco, sercret to cisco, and vty to cisco. 3 All the passwords are required to be encrypted. Lab Process: Router>enable Router#configure terminal Router(config)#hostname        / router set route name Router(config)#enable password         / cisco set router password Router(config)#enable secret cisco       Read more […] Read more »

CCNA ICND2 Lab13 – CHAP Authentication

Ensurepass Lab Tips: PPP supports device authentication through the two following protocols: PPP Authentication Protocol (PAP) and Challenge Handshake Authentication Protocol (CHAP). CHAP processes the password through Basic MD5 HASH algorithm and sends the processed data. The authentication experiences three handshakes. Topology: Lab Requirements: 1. Specify a unique host name for the router. 2. Write the host name and password of the remote router. 3. Perform PPP encapsulation and CHAP authentication Read more […] Read more »

CCNA ICND2 Lab14 – Frame Relay

Ensurepass Lab Tips: The Frame-Relay protocol is a data-link layer packet switching protocol that is used in the line. The line only checks errors. These errors are solved by the upper-layer protocols such as TCP. The frame-relay is connection-oriented and provided by VC. VC is full-duplex and provides full connections at a low cost. Topology: Lab Requirements: 1. A Cisco router is used as a frame-relay switch. 2. Meet the frame-relay lab requirements. The figure above gives the specific parameters. Lab Read more […] Read more »