New Updated Cisco ICND2 200-101 Real Exam Download 221-230

Ensurepass

QUESTION 221

The output of the show frame-relay pvc command shows “PVC STATUS = INACTIVE”. What does this mean?

 

A.       The PVC is configured correctly and is operating normally, but no data packets have been detected for more than five minutes.

B.        The PVC is configured correctly, is operating normally, and is no longer actively seeking the address of the remote router.

C.        The PVC is configured correctly, is operating normally, and is waiting for interesting traffic to trigger a call to the remote router.

D.       The PVC is configured correctly on the local switch, but there is a problem on the remote end of the PVC.

E.        The PVC is not configured on the local switch.

 

Correct Answer: D

 

 

QUESTION 222

What are three reasons that an organization with multiple branch offices and roaming users might implement a Cisco VPN solution instead of point-to-point WAN links? (Choose three.)

 

A.       reduced cost

B.        better throughput

C.        broadband incompatibility

D.       increased security

E.        scalability

F.        reduced latency

 

Correct Answer: ADE

 

 

QUESTION 223

A network administrator wants to ensure that only the server can connect to port Fa0/1 on a Catalyst switch. The server is plugged into the switch Fa0/1 port and the network administrator is about to bring the server online. What can the administrator do to ensure that only the MAC address of the server is allowed by switch port Fa0/1? (Choose two.)

 

A.       Configure port Fa0/1 to accept connections only from the static IP address of the server.

B.        Employ a proprietary connector type on Fa0/1 that is incompatible with other host connectors.

C.        Configure the MAC address of the server as a static entry associated with port Fa0/1.

D.       Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address.

E.        Configure port security on Fa0/1 to reject traffic with a source MAC address other than that of the server.

F.        Configure an access list on the switch to deny server traffic from entering any port other than Fa0/1.

 

Correct Answer: CE

 

 

QUESTION 224

Refer to the exhibit. A technician has configured the FastEthernet 0/1 interface on Sw11 as an access link in VLAN 1. Based on the output from the show vlan brief command issued on Sw12, what will be the result of making this change on Sw11?

 

clip_image002

 

A.       Only the hosts in VLAN 1 on the two switches will be able to communicate with each other.

B.        The hosts in all VLANs on the two switches will be able to communicate with each other.

C.        Only the hosts in VLAN 10 and VLAN 15 on the two switches will be able to communicate with each other.

D.       Hosts will not be able to communicate between the two switches.

 

Correct Answer: D

 

 

QUESTION 225

Refer to the exhibit. What commands must be configured on the 2950 switch and the router to allow communication between host 1 and host 2? (Choose two.)

 

clip_image003

 

A.       Router(config)# interface fastethernet 0/0

Router(config-if)# ip address 192.168.1.1 255.255.255.0

Router(config-if)# no shut down

 

B.        Router(config)# interface fastethernet 0/0

Router(config-if)# no shut down

Router(config)# interface fastethernet 0/0.1

Router(config-subif)# encapsulation dot1q 10

Router(config-subif)# ip address 192.168.10.1 255.255.255.0

Router(config)# interface fastethernet 0/0.2

Router(config-subif)#encapsulation dot1q 20

Router(config-subif)# ip address 192.168.20.1 255.255.255.0

 

C.        Router(config)# router eigrp 100

Router(config-router)# network 192.168.10.0

Router(config- router)# network 192.168.20.0

 

D.       Switch1(config)#vlan database

Switch1(config-vlan)#vtp domain XYZ

Switch1(config-vlan)#vtp server

 

E.        Switch1 (config)# interface fastethernet 0/1

Switch1 (config-if)# switchport mode trunk

 

F.        Switch1 (config)# interface vlan 1

Switch1 (config-if)# ip default-gateway 192.168.1.1

 

Correct Answer: BE

 

 

QUESTION 226

Refer to the exhibit. The output that is shown is generated at a switch. Which three of these statements are true? (Choose three.)

 

clip_image004

 

A.       All ports will be in a state of discarding, learning, or forwarding.

B.        Thirty VLANs have been configured on this switch.

C.        The bridge priority is lower than the default value for spanning tree.

D.       All interfaces that are shown are on shared media.

E.        All designated ports are in a forwarding state.

F.        This switch must be the root bridge for all VLANs on this switch.

 

Correct Answer: ACE

 

 

QUESTION 227

Refer to the exhibit. Which switch provides the spanning-tree designated port role for the network segment that services the printers?

 

clip_image006

 

A.       Switch1

B.        Switch2

C.        Switch3

D.       Switch4

 

Correct Answer: C

 

 

QUESTION 228

Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)

 

A.       802.1Q native VLAN frames are untagged by default.

B.        802.1Q trunking ports can also be secure ports.

C.        802.1Q trunks can use 10 Mb/s Ethernet interfaces.

D.       802.1Q trunks require full-duplex, point-to-point connectivity.

E.        802.1Q trunks should have native VLANs that are the same at both ends.

 

Correct Answer: ACE

 

 

QUESTION 229

Which set of commands is recommended to prevent the use of a hub in the access layer?

 

A.       switch(config-if)#switchport mode trunk

switch(config-if)#switchport port-security maximum 1

 

B.        switch(config-if)#switchport mode trunk

switch(config-if)#switchport port-security mac-address 1

 

C.        switch(config-if)#switchport mode access

switch(config-if)#switchport port-security maximum 1

 

D.       switch(config-if)#switchport mode access

switch(config-if)#switchport port-security mac-address 1

 

Correct Answer: C

 

 

QUESTION 230

Refer to the exhibit. A frame on VLAN 1 on switch S1 is sent to switch S2 where the frame is received on VLAN 2. What causes this behavior?

 

clip_image008

clip_image009

 

clip_image010

 

A.       trunk mode mismatches

B.        allowing only VLAN 2 on the destination

C.        native VLAN mismatches

D.       VLANs that do not correspond to a unique IP subnet

 

Correct Answer: C

 

Download Latest Complete Collection of ICND2 200-101 Real Exam ,help you to pass exam 100%.

Ensurepass Cisco Certifications Exam Questions and Answers
Ensurepass CCNA Exams Questions and Answers

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.