New Updated Cisco CCNP 642-902 Real Exam Download 51-60

Ensurepass

QUESTION 51

Which two statements about the EIGRP DUAL process are correct? (Choose two.)

 

A.       An EIGRP route will go active if there are no successors or feasible successors in the EIGRP topology table.

B.       An EIGRP route will go passive if there are no successors in the EIGRP topology table.

C.       DUAL will trigger an EIGRP query process while placing the flapping routes in the holddown state.

D.       A feasible successor in the EIGRP topology table can become the successor only after all the query requests have been replied to.

E.        The stuck in active state is caused when the wait for the query replies have timed out.

F.        EIGRP queries are sent during the loading state in the EIGRP neighbor establishment process.

 

Correct Answer: AE

 

 

QUESTION 52

What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub and spoke network? (Choose three.)

 

A.       A hub router prevents routes from being advertised to the remote router.

B.       Only remote routers are configured as stubs.

C.       Stub routers are not queried for routes.

D.      Spoke routers connected to hub routers answer the route queries for the stub router.

E.       A stub router should have only EIGRP hub routers as neighbors.

F.        EIGRP stub routing should be used on hub routers only.

 

Correct Answer: BCE

 

 

QUESTION 53

Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summarization is enabled on routers R2 and R3, but it is disabled on router R1. Which two EIGRP routes will be seen in the routing table of router R3? (Choose two.)

 

clip_image001

 

A.        10.0.0.0/8

B.        10.10.0.0/16

C.        10.10.10.0/24

D.        172.16.0.0/16

E.         172.16.0.0/24

F.         172.16.10.0/24

 

Correct Answer: CD

 

 

QUESTION 54

Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribution is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?

 

clip_image002

 

A.       the routes originating from the RIP routing domain

B.       the routes originating from the OSPF stub area

C.       all OSPF inter and intra-area routes

D.      all routes originating from RIP and OSPF routing domains

 

Correct Answer: A

 

 

QUESTION 55

Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2. What could be the cause of the problem?

 

clip_image003

 

A.       The no auto-summary command has not been issued under the EIGRP process on both routers.

B.       Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.

C.       EIGRP cannot exchange routing updates with a neighbor’s router interface that is configured with two IP addresses.

D.       EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.

 

Correct Answer: D

 

 

QUESTION 56

Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:

 

*Mar 20 12:12:06: %DUAL-5-NBRCHANGE. IP-EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down:

stuck in active

*Mar 20 12:15:23: %DUAL-3-SIA. Route 10.1.1.0/24 stuck-in-active state in IP-EIGRP 1. Cleaning up

 

The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network. Which statement best describes the reason for the error messages?

 

clip_image004

 

A.       Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.

B.       Incorrect bandwidth configuration on router R5 prevents R2 from establishing neighbor adjacency.

C.       Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .

D.       Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .

 

Correct Answer: C

 

 

QUESTION 57

Which EIGRP packet statement is true?

 

A.       On high-speed links, hello packets are broadcast every 5 seconds for neighbor discovery.

B.       On low-speed links, hello packets are broadcast every 15 seconds for neighbor discovery.

C.       Reply packets are multicast to IP address 224.0.0.10 using RTP.

D.      Update packets route reliable change information only to the affected routers.

E.       Reply packets are used to send routing updates.

 

Correct Answer: D

 

 

QUESTION 58

Refer to the exhibit. EIGRP has been configured on all routers in the network. The command metric weights 0 0 1 0 0 has been added to the EIGRP process so that only the delay metric is used in the path calculations. Which router will R1 select as the successor and feasible successor for Network A?

 

clip_image005

 

A.       R4 becomes the successor for Network A and will be placed in the routing table. R2 becomes the feasible successor for Network A.

B.       R4 becomes the successor for Network A and will be included in the routing table. No feasible successor will be selected as the advertised distance from R2 is higher than the feasible distance.

C.       R2 becomes the successor and will be placed in the routing table. R4 becomes the feasible successor for Network A.

D.       R2 becomes the successor and will be placed in the routing table. No feasible successor will be selected as the reported distance from R4 is lower than the feasible distance.

 

Correct Answer: B

 

 

QUESTION 59

During a redistribution of routes from OSPF into EIGRP, an administrator notices that none of the OSPF routes are showing in EIGRP. What are two possible causes? (Choose two.)

 

A.       incorrect distribute lists have been configured

B.       missing ip classless command

C.       CEF not enabled

D.      no default metric configured for EIGRP

 

Correct Answer: AD

 

 

QUESTION 60

Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?

 

clip_image006

 

A.  Issue the command bandwidth 56 on each subinterface.

B.  Issue the command bandwidth 224 on each subinterface.

C.  Issue the command bandwidth 56 on the physical interface.

D.  Issue the command bandwidth 224 on the physical interface.

 

Correct Answer: D

 

Download Latest Complete Collection of CCNP 642-902 Real Exam ,help you to pass exam 100%.

Ensurepass Cisco Certifications Exam Questions and Answers
Ensurepass CCNP Exams Questions and Answers

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.