New Updated Cisco CCNA R&S 200-120 Real Exam Download 301-310



Which protocol can cause overload on a CPU of a managed device?


A.      Netflow

B.      WCCP

C.      IP SLA

D.      SNMP


Correct Answer: D




What are the three things that the Netflow uses to consider the traffic to be in a same flow?


A.      IP address

B.      Interface name

C.      Port numbers

D.      L3 protocol type

E.       MAC address


Correct Answer: ACD




What is the alert message generated by SNMP agents called?


A.      TRAP

B.      INFORM

C.      GET

D.      SET


Correct Answer: AB




Which three features are added in SNMPv3 over SNMPv2?


A.      Message Integrity

B.      Compression

C.      Authentication

D.      Encryption

E.       Error Detection


Correct Answer: ACD




In a GLBP network, who is responsible for the arp request?


A.      AVF

B.      AVG

C.      Active Router

D.      Standby Router


Correct Answer: B




Which one of these is a valid HSRP Virtual Mac Address?


A.      0000.0C07.AC01

B.      0000.5E00.0110

C.      0007.B400.1203

D.      0000.C007.0201


Correct Answer: A




What levels will be trapped if the administrator executes the command (Choose four.)


router(cfg)#logging trap 4


A.      Emergency

B.      Notice

C.      Alert

D.      Error

E.       Warning


Correct Answer: ACDE




What are the three things that netflow uses to consider the traffic to be in a same flow?


A.      IP address

B.      Interface name

C.      Port numbers

D.      L3 protocol type


Correct Answer: ACD




Which is true about OSPF router-id? (Choose two.)


A.      It is used for type 1 router LSA

B.      Highest IP address of the loopback is used

C.      router-id needs to be matched on ospf neighbors

D.      router-id is 16 bit


Correct Answer: AB





After adding BLD-102 router, no routing updates are being exchanged between BLD-102 and the new location. All other inter connectivity and Internet access for the existing locations of the company are working properly.

The task is to identify the fault(s) and correct the router configuration to provide full connectivity between the routers.

Access to the router CLI can be gained by clicking on the appropriate host. All passwords on all routers are cisco.

IP addresses are listed in the chart below.



Correct Answer:

EIGRP Lab is a troubleshooting problem, use the command show run to find the topology diagram four EIGRP router configuration errors and corrections, so that the network is the all-pass completion of the experiment. There are two types of errors: 1. AS number is wrong; 2.Segment declaration is wrong. Be remember after finishing each segment ping about whether the pass. Finally remember Copy running-config Startup-config.



BLD-102>enable (Need to enter the password cisco)

BLD-102#configure terminal



AS number is wrong, you need to delete the entire eigrp, re-declaration.


BLD-102(config)#no router eigrp 22

BLD-102(config)#router eigrp 122



BLD-102(config-router)#no auto-summary


BLD-102#copy running-config startup-config


Campus>enable (Need to enter the password cisco)



Campus#configure terminal

Campus(config)#router eigrp 122


Campus(config-router)#no network


Campus#copy running-config startup-config


This router has a passive-interface S1/0 configuration, there is no error, without treatment.


Download Latest Complete Collection of CCNA R&S 200-120 Real Exam ,help you to pass exam 100%.

Ensurepass Cisco Certifications Exam Questions and Answers
Ensurepass CCNA R&S Exams Questions and Answers

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.