Latest CompTIA Server+ SK0-003 Real Exam Download 71-80



A server in a manufacturing environment needs to receive input from multiple measurement devices on the production line. Which of the following would be needed on the server?


A.      HBA card

B.      SCSI card

C.      Serial card

D.      Video card


Correct Answer: C




A server technician has been attempting to install an operating system on the company test server for several days. The technician has experienced error messages at several points of the installation and the system has frozen during various parts of the boot process. The technician has replaced the power supply, graphics card and installation disk with known good components. Which of the following could be causing these issues? (Select TWO).


A.      Storage driver not loaded

B.      Fragmented hard drive

C.      Damaged or faulty NIC chipset

D.      Damaged or faulty system board

E.       Memory incompatible with the processor

F.       Missing voltage regulator


Correct Answer: DE




A Windows user is trying to get to a shared folder on a server but is receiving an error message that multiple connections to the same resource are not allowed. Which of the following tools can the technician use from the user’s workstation to get the user reconnected as quickly as possible?


A.      nbtstat with the /reload parameter

B.      nbtstat with the /resolved parameter

C.      net use with the /delete parameter

D.      net use with the /persistent parameter


Correct Answer: C




Which of the following BEST describes a Blade server?


A.      Provides higher levels of physical redundancy than a typical server

B.      Provides better rack space utilization than a typical server

C.      Is 1.75 inches in height to fit properly in a rack

D.      Uses an unshared backplane


Correct Answer: B




An administrator is working on a rack mount server with all newly installed equipment. The uninterruptible power supply (UPS) in the rack starts beeping loudly. Which of the following is the FIRST troubleshooting step that should be taken?


A.      Ensure that the power cable for the UPS is plugged in.

B.      Ensure the battery in the UPS is still good.

C.      Check the smart cable connecting the UPS to the server.

D.      Reset the UPS to determine if the problem persists.


Correct Answer: A




Which of the following is MOST likely to occur if the temperature in the server room is cooled too quickly after a power outage?


A.      Server forms condensation

B.      Server will not POST

C.      Server’s services will not start

D.      Server response times are slow due to temperature change


Correct Answer: A




An administrator needs to explain to management why updates are needed for the server. Which of the following is the BEST explanation to give?


A.      The updates guarantee that the server will work smoothly.

B.      The updates show management that IT is working diligently.

C.      The updates address driver and security issues.

D.      The updates are needed to allow the system monitoring agents to connect to the system.


Correct Answer: C




An administrator has just installed a new NIC into the server. The system POSTs fine and the NIC is recognized by the OS, but it does not receive an IP address. Which of the following is the MOST likely cause of this?


A.      The NIC is not on the HCL.

B.      The driver is incorrect on the server.

C.      The patch cable has not been seated properly.

D.      The NIC is not seated properly.


Correct Answer: C




A file server is setup in a RAID 5 configuration. Recently there was a power failure in the server room while a user was transferring a document from one drive on the server to another drive on the same server. Unfortunately their UPS was in repair during this outage, and the file is now corrupt. Which of the following can be done to prevent this situation in the future?


A.      Increase the memory on the server.

B.      Reconfigure drives to a RAID 0+1.

C.      Install a battery backed write cache module in the system.

D.      Instruct the user to save to the local system instead of to the server.


Correct Answer: C




An administrator has a single 14U rack. The administrator needs to install fifteen servers; rack- mounted redundant uninterruptible power supplies (UPSs), a network switch, and a KVM. Which of the following server types would be BEST suited for this scenario?


A.      Blade servers

B.      Rackmount servers

C.      Tower servers

D.      Web servers


Correct Answer: A



Download Latest Server+ SK0-003 Real Free Tests , help you to pass exam 100%.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.