[Free] New Updated (October) Cisco 200-120 Real Exam 151-160




If IP routing is enabled, which two commands set the gateway of last resort to the default gateway? (Choose two.)


A.      ip default-gateway

B.      ip route

C.      ip default-network

D.      ip default-route

E.       ip route


Correct Answer: CE



Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used?


A.      hop count

B.      administrative distance

C.      link bandwidth

D.      link delay

E.       link cost


Correct Answer: B




Refer to the exhibit.




A network associate has configured OSPF with the command:


City(config-router)# network area 0


After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three.)


A.      FastEthernet0 /0

B.      FastEthernet0 /1

C.      Serial0/0

D.      Serial0/1.102

E.       Serial0/1.103

F.       Serial0/1.104


Correct Answer: BCD




Refer to the exhibit. The Lakeside Company has the internetwork in the exhibit. The administrator would like to reduce the size of the routing table on the Central router. Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?




A. is
subnetted, 1 subnets

D [90/20514560] via, 6w0d, Serial0/1

B. is subnetted, 1 subnets

D [90/20514560] via, 6w0d, Serial0/1

C. is subnetted, 1 subnets

D [90/20514560] via, 6w0d, Serial0/1

D.      0.0.0/22 is subnetted, 1 subnets

D [90/20514560] via, 6w0d, Serial0/1

E. is subnetted, 1 subnets

D [90/20514560] via, 6w0d, Serial0/1

F. is subnetted, 1 subnets

D [90/20514560] via, 6w0d, Serial0/1


Correct Answer: D



Refer to the graphic. A static route to the network is to be configured on the HFD router. Which commands will accomplish this? (Choose two.)




A.      HFD(config)# ip route fa0/0

B.      HFD(config)# ip route

C.      HFD(config)# ip route fa0/0

D.      HFD(config)# ip route

E.       HFD(config)# ip route

F.       HFD(config)# ip route


Correct Answer: CD




Before installing a new, upgraded version of the IOS, what should be checked on the router, and which command should be used to gather this information? (Choose two.)


A.      the amount of available ROM

B.      the amount of available flash and RAM memory

C.      the version of the bootstrap software present on the router

D.      show version

E.       show processes

F.       show running-config


Correct Answer: BD




Which command reveals the last method used to powercycle a router?


A.      show reload

B.      show boot

C.      show running-config

D.      show version


Correct Answer: D




Which command would you use on a Cisco router to verify the Layer 3 path to a host?


A.      tracert address

B.      traceroute address

C.      telnet address

D.      ssh address


Correct Answer: B




What information does a router running a link-state protocol use to build and maintain its topological database? (Choose two.)


A.      hello packets

B.      SAP messages sent by other routers

C.      LSAs from other routers

D.      beacons received on point-to-point links

E.       routing tables received from other link-state routers

F.       TTL packets from designated routers


Correct Answer: AC




Which statements describe the routing protocol OSPF? (Choose three.)


It supports VLSM.

B.      It is used to route between autonomous systems.

C.      It confines network instability to one area of the network.

D.      It increases routing overhead on the network.

E.       It allows extensive control of routing updates.

F.       It is simpler to configure than RIP v2.


Correct Answer: ACE

Free VCE & PDF File for Cisco 200-120 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …