[Free] New Updated (October) Cisco 200-101 Real Exam 231-240

Ensurepass

 

QUESTION 231

A network administrator receives an error message while trying to configure the Ethernet interface of a router with IP address 10.24.24.24/29. Which statement explains the reason for this issue?

 

A.       VLSM-capable routing protocols must be enabled first on the router.

B.        This address is a network address.

C.        This address is a broadcast address

D.       The Ethernet interface is faulty.

 

Correct Answer: B

 

 

QUESTION 232

You are working in a data center environment and are assigned the address range 10.188.31.0/23. You are asked to develop an IP addressing plan to allow the maximum number of subnets with as many as 30 hosts each. Which IP address range meets these requirements?

 

A.        10.188.31.0/26

B.        10.188.31.0/25

C.        10.188.31.0/28

D.        10.188.31.0/27

E.         10.188.31.0/29

 

Correct Answer: D

 

 

QUESTION 233

Which IPv6 address is valid?

 

A.       2001:0db8:0000:130F:0000:0000:08GC:140B

B.        2001:0db8:0:130H::87C:140B

C.        2031::130F::9C0:876A:130B

D.       2031:0:130F::9C0:876A:130B

 

Correct Answer: D

 

 

QUESTION 234

Which statements are true about EIGRP successor routes? (Choose two.)

 

A.       A successor route is used by EIGRP to forward traffic to a destination.

B.        Successor routes are saved in the topology table to be used if the primary route fails.

C.        Successor routes are flagged as “active” in the routing table.

D.       A successor route may be backed up by a feasible successor route.

E.        Successor routes are stored in the neighbor table following the discovery process.

 

Correct Answer: AD

 

 

QUESTION 235

What can be done to secure the virtual terminal interfaces on a router? (Choose two.)

 

A.       Administratively shut down the interface.

B.        Physically secure the interface.

C.
       
Create an access list and apply it to the virtual terminal interfaces with the access-group command.

D.       Configure a virtual terminal password and login process.

E.        Enter an access list and apply it to the virtual terminal interfaces using the access-class command.

 

Correct Answer: DE

 

 

QUESTION 236

Refer to the exhibit. Assume that all router interfaces are operational and correctly configured. In addition, assume that OSPF has been correctly configured on router R2. How will the default route configured on R1 affect the operation of R2?

 

clip_image002

 

A.       Any packet destined for a network that is not directly connected to router R1 will be dropped.

B.        Any packet destined for a network that is not directly connected to router R2 will be dropped immediately.

C.        Any packet destined for a network that is not directly connected to router R2 will be dropped immediately because of the lack of a gateway on R1.

D.       The networks directly connected to router R2 will not be able to communicate with the 172.16.100.0, 172.16.100.128, and 172.16.100.64 subnetworks.

E.        Any packet destined for a network that is not referenced in the routing table of router R2 will be directed to R1. R1 will then send that packet back to R2 and a routing loop will occur.

 

Correct Answer: E

 

 

QUESTION 237

Refer to the exhibit. The network is converged. After link-state advertisements are received from Router_A, what information will Router_E contain in its routing table for the subnets 208.149.23.64 and 208.149.23.96?

 

clip_image004

 

A.      208.149.23.64[110/13] via 190.173.23.10,00:00:07, FastEthemet0/0

208.149.23.96[110/13] via 190.173.23.10,00:00:16, FastEthemet0/0

 

B.      208.149.23.64[110/1] via 190.172.23.10,00:00:07, Serial1/0

208.149.23.96[110/3] via 190.173.23.10,00:00:16, FastEthemet0/0

 

C.      208.149.23.64[110/13] via 190.173.23.10,00:00:07, Serial1/0

208.149.23.96[110/13] via 190.173.23.10,00:00:16, Serial1/0

208.149.23.96[110/13] via 190.173.23.10,00:00:16, FastEthemet0/0

 

D.      208.149.23.96[110/3] via 190.173.23.10,00:00:16, Serial1/0

208.149.23.96[110/3] via 190.173.23.10,00:00:16, Serial1/0

 

Correct Answer: A

 

 

QUESTION 238

Refer to the exhibit. When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?

 

clip_image005

 

A.       AS numbers must be changed to match on all the routers.

B.        Loopback interfaces must be configured so a DR is elected.

C.        The no auto-summary command is needed on Router A and Router C.

D.       Router B needs to have two network statements, one for each connected network.

 

Correct Answer: A

 

 

QUESTION 239

Which command reveals the last method used to powercycle a router?

 

A.       show reload

B.        show boot

C.        show running-config

D.       show version

 

Correct Answer: D

 

 

 

 

 

QUESTION 240

Which two statements are characteristics of a distance vector routing protocol? (Choose two.)

 

A.       Each router has its own view of the topology.

B.        Updates are periodic and include the entire routing table.

C.        Routing updates are sent only after topology changes.

D.       Convergence is usually faster than with link state protocols.

E.        RIP is an example of distance vector routing protocols.

F.        The protocol can be useful in hub-and-spoke and hierarchical networks.

 

Correct Answer: BE

Free VCE & PDF File for Cisco 200-101 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …