[Free] New Updated (October) Cisco 200-101 Real Exam 221-230




Refer to the exhibit. What commands must be configured on the 2950 switch and the router to allow communication between host 1 and host 2? (Choose two.)




A.       Router(config)# interface fastethernet 0/0

Router(config-if)# ip address

Router(config-if)# no shut down


B.        Router(config)# interface fastethernet 0/0

Router(config-if)# no shut down

Router(config)# interface fastethernet 0/0.1

Router(config-subif)# encapsulation dot1q 10

Router(config-subif)# ip address

Router(config)# interface fastethernet 0/0.2

Router(config-subif)#encapsulation dot1q 20

Router(config-subif)# ip address


C.        Router(config)# router eigrp 100

Router(config-router)# network

Router(config- router)# network


D.       Switch1(config)#vlan database

Switch1(config-vlan)#vtp domain XYZ

Switch1(config-vlan)#vtp server


A.       Switch1 (config)# interface fastethernet 0/1

Switch1 (config-if)# switchport mode trunk

B.        Switch1 (config)# interface vlan 1

Switch1 (config-if)# ip default-gateway


Correct Answer: BE




Refer to the exhibit. The output that is shown is generated at a switch. Which three of these statements are true? (Choose three.)




A.       All ports will be in a state of discarding, learning, or forwarding.

B.        Thirty VLANs have been configured on this switch.

C.        The bridge priority is lower than the default value for spanning tree.

D.       All interfaces that are shown are on shared media.

E.        All designated ports are in a forwarding state.

F.        This switch must be the root bridge for all VLANs on this switch.


Correct Answer: ACE













Refer to the exhibit. Which switch provides the spanning-tree designated port role for the network segment that services the printers?




A.       Switch1

B.        Switch2

C.        Switch3

D.       Switch4


Correct Answer: C




Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)


A.       802.1Q native VLAN frames are untagged by default.

B.        802.1Q trunking ports can also be secure ports.

C.        802.1Q trunks can use 10 Mb/s Ethernet interfaces.

D.       802.1Q trunks require full-duplex, point-to-point connectivity.

E.        802.1Q trunks should have native VLANs that are the same at both ends.


Correct Answer: ACE






Which set of commands is recommended to prevent the use of a hub in the access layer?


A.       switch(config-if)#switchport mode trunk

switch(config-if)#switchport port-security maximum 1


B.        switch(config-if)#switchport mode trunk

switch(config-if)#switchport port-security mac-address 1


C.        switch(config-if)#switchport mode access

switch(config-if)#switchport port-security maximum 1


D.       switch(config-if)#switchport mode access

switch(config-if)#switchport port-security mac-address 1


Correct Answer: C




Refer to the exhibit. A frame on VLAN 1 on switch S1 is sent to switch S2 where the frame is received on VLAN 2. What causes this behavior?







A.       trunk mode mismatches

B.        allowing only VLAN 2 on the destination

C.        native VLAN mismatches

D.       VLANs that do not correspond to a unique IP subnet


Correct Answer: C




Which three statements about RSTP are true? (Choose three.)


A.       RSTP significantly reduces topology reconverging time after a link failure.

B.        RSTP expands the STP port roles by adding the alternate and backup roles.

C.        RSTP port states are blocking, discarding, learning, or forwarding.

D.       RSTP provides a faster transition to the forwarding state on point-to-point links than STP does.

E.        RSTP also uses the STP proposal-ag
reement sequence.

F.        RSTP uses the same timer-based process as STP on point-to-point links.


Correct Answer: ABD




Assuming the default switch configuration, which VLAN range can be added, modified, and removed on a Cisco switch?


A.       1 through 1001

B.        2 through 1001

C.        1 through 1002

D.       2 through 1005


Correct Answer: B




The ROUTE Company has a small network. The network consists of one switch and one router. The switch has been configured with two VLANs. The router has been configured as a router-on- a-stick to allow inter- VLAN routing. A trunk is configured to connect the switch to the router. What is the minimum number of router subinterfaces that are required for all the VLANs to communicate?


A.       zero

B.        one

C.        two

D.       three


Correct Answer: C



TION 230

Identify the four valid IPv6 addresses. (Choose four.)


A.       ::

B.        ::192:168:0:1

C.        2000::

D.       2001:3452:4952:2837::

E.        2002:c0a8:101::42

F.        2003:dead:beef:4dad:23:46:bb:101


Correct Answer: ABEF

Free VCE & PDF File for Cisco 200-101 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …