[Free] New Updated (October) Cisco 200-101 Real Exam 191-200

Ensurepass

 

QUESTION 191

Refer to the exhibit. At the end of an RSTP election process, which access layer switch port will assume the discarding role?

 

clip_image002

 

A.       Switch3, port fa0/1

B.        Switch3, port fa0/12

C.        Switch4, port fa0/11

D.       Switch4, port fa0/2

E.        Switch3, port Gi0/1

F.        Switch3, port Gi0/2

 

Correct Answer: C

QUESTION 192

Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the most likely reason that interface FastEthernet 0/10 is not the root port for VLAN 2?

 

clip_image004

 

A.       This switch has more than one interface connected to the root network segment in VLAN 2.

B.        This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.

C.        This switch interface has a higher path cost to the root bridge than another in the topology.

D.       This switch has a lower bridge ID for VLAN 2 than the elected designated switch.

 

Correct Answer: C

 

 

QUESTION 193

Select the action that results from executing these commands.

 

Switch(config-if)# switchport port-security

Switch(config-if)# switchport port-security mac-address sticky

 

A.       A dynamically learned MAC address is saved in the startup-configuration file.

B.        A dynamically learned MAC address is saved in the running-configuration file.

C.        A dynamically learned MAC address is saved in the VLAN database.

D.       Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.

E.        Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.

 

Correct Answer: B

 

 

 

 

 

QUESTION 194

Refer to the exhibit. Some 2950 series switches are connected to the conference area of the corporate headquarters network. The switches provide two to three jacks per conference room to host laptop connections for employees who visit the headquarters office. When large groups of employees come from other locations, the network administrator often finds that hubs have been connected to wall jacks in the conference area although the ports on the access layer switches were not intended to support multiple workstations. What action could the network administrator take to prevent access by multiple laptops through a single switch port and still leave the switch functional for its intended use?

 

clip_image005

 

A.       Configure static entries in the switch MAC address table to include the range of addresses used by visiting employees.

B.        Configure an ACL to allow only a single MAC address to connect to the switch at one time.

C.        Use the mac-address-table 1 global configuration command to limit each port to one source MAC address.

D.       Implement Port Security on all interfaces and use the port-security maximum 1 command to limit port access to a single MAC address.

E.        Implement Port Security on all interfaces and use the port-security mac-address sticky command to limit access to a single MAC address.

F.        Implement Port Security at global configuration mode and use the port-security maximum 1 command to allow each switch only one attached hub.

 

Correct Answer: D

QUESTION 195

Refer to the exhibit. Which two statements about the configuration of the switch interface are correct? (Choose two.)

 

clip_image007

 

A.       The switchport belongs only to VLAN 2.

B.        By default, all switch ports are members of VLAN 1005.

C.        Interface fa0/0 will be in both VLAN 1 (by default) and VLAN 2.

D.       The exhibit shows interface fa0/0 to be dynamically mapped to VLAN 2.

E.        A network host can be connected to this interface.

 

Correct Answer: AE

 

 

QUESTION 196

Refer to the exhibit. Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.)

 

clip_image008

 

< font color="#000000">A.       SwitchA, Fa0/2, designated

B.        SwitchA, Fa0/1, root

C.        SwitchB, Gi0/2, root

D.       SwitchB, Gi0/1, designated

E.        SwitchC, Fa0/2, root

F.        SwitchD, Gi0/2, root

 

Correct Answer: ABF

 

 

QUESTION 197

Which three elements must be used when you configure a router interface for VLAN trunking? (Choose three.)

 

A.       one physical interface for each subinterface

B.        one IP network or subnetwork for each subinterface

C.        a management domain for each subinterface

D.       subinterface encapsulation identifiers that match VLAN tags

E.        one subinterface per VLAN

F.        subinterface numbering that matches VLAN tags

 

Correct Answer: BDE

 

 

QUESTION 198

Which three statements about VTP features are true? (Choose three.)

 

A.       VTP works at Layer 3 of the OSI model and requires that a management VLAN IP address be configured.

B.        When properly configured, VTP minimizes VLAN misconfigurations and configuration inconsistencies.

C.        When properly configured, VTP maintains VLAN configuration consistency and accelerates trunk link negotiation.

D.       Each broadcast domain on a switch can have its own unique VTP domain.

E.        VTP pruning is used to increase available bandwidth in trunk links.

F.        To configure a switch to be part of two VTP domains, each domain must have its own passwords.

G.       Client, server, and transparent are valid VTP modes.

 

Correct Answer: BEG

 

 

 

 

 

 

QUESTION 199

Two switches are connected through a trunk link. Which two commands show that there is a native VLAN mismatch on that link? (Choose two.)

 

A.       show vlan brief

B.        show interface trunk

C.        show interface vlan

D.       show interface switchport

E.&nbsp
;      
show interface interface

F.        show switchport trunk

 

Correct Answer: BD

 

 

QUESTION 200

Which two of these statements are true of IPv6 address representation? (Choose two.)

 

A.       There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.

B.        A single interface may be assigned multiple IPv6 addresses of any type.

C.        Every IPv6 interface contains at least one loopback address

D.       The first 64 bits represent the dynamically created interface ID.

E.        Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.

 

Correct Answer: BC

Free VCE & PDF File for Cisco 200-101 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …