Free- Exam Objective 3.4 – Dumps4shared

A plus 220-1001 – Exam Objective 3.4

A+ Exam Objective 3.4

Click here if you want to go back to the A+ 220-1001 Table of Content

3.4 Given a scenario, select, install, and configure storage devices.

Click here for our A+ Exam Simulator for exams 220-1001 & 220-1002

Welcome to Exam Notes by Dumps4shared! In this article, we
will cover Core 1 objective 3.4 Given a scenario, select, install, and
configure storage devices.

Optical Drives/Media Capacity

CD-ROM / CD-RW

CD-ROMs are optical media drives that
read round plastic discs which contain an aluminum or dye coating on one side. This
coating contains pits and lands or binary ons and offs. CD-ROMs are mass
produced by music or software distributors and are read-only. The maximum
capacity for a CD-ROM is 700 MB of data or 80 minutes of audio. Don’t forget to
allow 2 seconds between each track if you are cutting it close. 

CD-Rs and CD-RWs are
writable CD-ROMs. CD-Rs can only be written once while CD-RWs are rewritable,
meaning the data on them can be completely overwritten with new data or the
disc can be erased. Writing to a writable CD media requires a CD-RW drive.
Since these drives use a red laser to write to the recordable dye in the
backing, CD-RW drives are referred to as a burner. CD-RW drives are most
commonly internal devices (PATA / SATA) but can also be quite useful as a
portable device, allowing you to back up data before working on a unit. You may
also see these drives’ write speed expressed as 52x or 48x where the x
indicates the increase in speed.

Pits and Lands in Optical media

Pits and Lands represent the ones and zeros in binary storage.
The raised dots or oblong bits displayed are the lands and the remaining space
on the disc are the pits. This technology is the same for all optical media.
Only the density of the lands varies, allowing for more data depending on the
size and density.

DVD-ROM / DVD-RW / DVD-RW DL

The same principles that apply to CD-ROMs apply to DVD-ROMs,
DVD-RWs, and DVD DLs. The capacity of the DVD disc increased to 4.7 GB. This is
accomplished by increasing the density of the pits and lands while still using
a red laser. It was discovered that the capacity of the DVD-ROM could be
doubled to 8.5 GB by using two layers of recordable dye. The laser can then focus
on one layer at a time. All of the DVD drives discussed will be either internal
(PATA / SATA) or external.

Blu-ray

Blu-ray (BD) technology is the
highest capacity consumer grade optical technology currently available. Blu-ray
uses a blue laser that has a shorter wavelength than the previous technologies,
allowing for higher density data storage. A Blu-ray disc has a capacity of 25
GB for a single layer disc and 50 GB for a dual layer disc. This dramatic
capacity increase allowed movie studios to distribute content that wouldn’t otherwise
fit on a DVD. Enhancements such as HD and 3D fit comfortably on a Blu-ray disc with
room for alternate formats and additional features.

BD-R

BD-R is the 25 GB Blu-ray write
once recordable disc. Blu-ray recordable discs use the same speed rating
identifiers that were used on CD and DVD technology. For example, a 1x BD-R
writes at roughly 36 Mbps and a 2x at 72 Mbps. 2x is considered to be the minimum
acceptable read speed for viewing BD-ROM movies. Considering that it would take
over 90 minutes for a 1x BD-R to write 25 GB of data, the need for speed is
important.

Also consider that your maximum write speed will be determined
by the slowest component: the drive or the media. You may have a 16x BD-R drive
but if your media is rated at 4x, it is unlikely that you will write at any
speed near 16x. Most Blu-ray devices will be backwards compatible to DVD and
CD-ROMs. Considered high end for PCs, the majority of these devices will be
internal and use the SATA 2.0 or higher connection in order to support the high
transfer rates. External BD-R drives are also available. These predominantly use
USB 2.0 and optimally USB 3.0.

BD-RE

BD-RE discs are rewriteable but otherwise,
use the same process as BD-R. This is an advantage even though disc prices are
coming down. The write speeds of BD-RE drives are comparable to that of BD-R
but there is some pre-write overhead that takes time. The BD-RE media must be
completely erased and verified before the write process can begin.

• Solid-state drives

 M2 drives

Solid state drives are highly beneficial in standard form
factors such as 2.5”. These drives can be used to upgrade the performance of
laptops with SATA connections. As consumers wanted smaller and thinner portable
devices, the M2 drive addressed the need by using the PCI Express Mini Card and
SATA compatibility. These drives offered the most storage and fastest speeds
while having a much smaller footprint in the device.

– NVME

Non-Volatile Memory Express (NVMe) evolved from the M2 standard and offered even greater speed. To get the most from an NVMe drive, use it as the boot device in the system. NVMe drives use the PCI Express x4 to provide the fastest performance.

Click here for our A+ Exam Simulator for exams 220-1001 & 220-1002

Magnetic hard disk drives

Magnetic hard disk drives are the primary storage device for
most computers on the market today. Solid state drives are coming down in price,
but you will find the cost per gigabyte is still the best for the magnetic hard
disk. These drives come in two main physical sizes: the 3.5” PC drive and the
2.5“ drive which is better suited to portable devices. Surprisingly, the iPod
Classic 160 GB media player contains a magnetic hard disk.

Inner view of a hard disk drive Seagate
Medalist ST33232A

When selecting a drive, consider the form factor and the
rotational speed of the disks. 2.5” disks are power efficient and compact, helping
reduce the overall size of portables while conserving battery life.

5400 rpm

The 2.5” disk is available with two platter rotation speeds. 5400 RPM drives
use less energy and are quieter, but do not offer the faster data rates that
can be achieved with a 7200 RPM drive.

7200 rpm / 10,000 rpm

The 7200
RPM
 drives on average consume more power.  The speed
difference will be tangible when moving large files or using disk intensive
programs. 3.5” disks are mainly used in desktop units. They are available with
three rotational speeds: 5400 RPM, 7200 RPM, and 10,000 RPM. 10,000
RPM drives are more expensive and less power efficient. When it comes to pure
performance in a magnetic storage device using access speed as the main
criteria, the 10, 000 RPM disk will always win. These are used in servers and
SAS (Serial Attached SCSI) devices. In addition to needing a SCSI controller,
the penalty for this kind of performance is heat, noise, and poor comparative
energy efficiency.

15,000rpm

15,000 rpm hard disks found their niche in SAS applications.
There is some debate as to whether they are cost efficient in terms of
capacity, noise, heat, and power consumption when compared to SSD drives.

Hybrid

Hybrid drives, or SSHD devices, strike the
balance between cost, performance, and capacity. By coupling a nominal amount
of solid state non-volatile memory with a terabyte or two of magnetic storage, the
time it take to boot and access frequently used program files can be decreased.
When presented with the option, your system’s firmware will store this data in
the hybrid or cache portion of storage, making it rapidly accessible when you
reload the program or even reboot since the data on the SSD persists without
power and will be instantly available.

Flash – Be
sure to write protect these devices when using them portably as the risk of
data loss or virus infection is very real. As the technology progressed, so did
the packaging and the capacity. Since they are small and don’t take too much
space, slots for these solid state memory packages were built directly into laptops,
offering safe and efficient portability of data. Yes, this was before the Cloud.
There really is no substitute for having a “hard copy” of your data and these smaller,
more efficient storage mediums continue to proliferate.

Compact Flash and SD

Laptop manufacturers support one or two package types, but not
all. The most convenient solution to this problem of design compatibility was
to create a portable USB memory card reader that would support all types of
memory cards such as the one shown below. If you look closely, you can see
that the multi-card reader will accept SD cards, Compact Flash, Micro-SD, and Mini-SD
storage cards. It’s nice to have one of these handy.

Raid types

This section covers all of the technology
associated with RAID. RAID is shorthand for a Redundant Array of Independent
Disks. This technology allows multiple disks to appear as a single volume. The
disks are capable of creating mirrored images of other drives and maintaining a
consistent backup of a particular disk. Some RAID configurations are very fault
tolerant.

RAID assigns different numeric qualities to each level. There is
Hardware based RAID and Software based RAID. The most prevalent are RAID 0,
RAID 1, RAID 5, and Raid 10. We will explain below what makes them different.
There is another RAID array, called JBOD or Just a Bunch of Disks, that only
requires two or more disks and the data is spanned across them. This array has
no fault tolerance or redundancy. The most prevalent RAID array configurations
are explained below.

RAID 0

RAID 0 uses two or more drives and
is used to increase the size of the volume available. The data on the volume is
treated sequentially and will be written across all drives in the array. There
is no parity. If a drive in the array fails, the volume fails.

RAID 1

RAID 1 also requires two disks to be
paired together. You would think that using identical hardware, combining the
drives would double the volume size. With mirroring this is not the case. In
RAID 1, the second drive is used as a mirror. When you write data to the
mirrored set, you write to both of the drives at the same time and read
requests can be handled by either drive.

RAID 5

RAID 5 arrays are quite special,
especially in the way they store and manage data. The minimum requirement is three
physical disks. In this configuration, there is a performance and fault
tolerance and an increase in speed through the use of parity. When data is written,
it is spread across the available drives except the parity drive. Each disk
will contain both parity and standard data. If a drive fails, there is enough
information to completely rebuild the drives in minutes, not hours that a
backup based restore would take.

Raid 10

RAID 10 is the most recent RAID development and is also known as RAID 1+0. RAID 10 combines RAID 1 and RAID 0. The disk requirement is a minimum of four disks where two drives are mirrored and two drives are striped, making this the most robust storage solution available.

Hot swappable drives

Hot swappable drives provide
storage flexibility for PCs and laptops through an external interface that allows
hard disks to be added or removed without the need to power down the machine.
Originally this was a complex operation, but the introduction of USB and SATA
technologies combine to make this a reasonably safe process. The configuration
can be a single drive or an enclosure that houses multiple drives which can be
swapped in and out as necessary. It is a good idea to check the write caching
status on your drive dock that you intend to swap your drives on. This is
disabled by default but it’s best to turn this on to allow recovery of lost
data. You will find this setting in the Device Manager in the properties of the
device.

That’s all for 3.4! Keep studying and good luck on the test!

Click here if you want to go back to the A+ 220-1001 Table of Content

Click here for our A+ Exam Simulator for exams 220-1001 & 220-1002


Pass Your IT Certification Exams With Free Real Exam Dumps and Questions

Full Version 220-1002 Dumps