[Free] Download New Updated (December) Cisco 642-035 Exam Questions 81-90

Ensurepass

QUESTION 81

For a KVM session to be successful, which two of these need to be done? (Choose two.)

 

A.

The Cisco IMC IP address needs to be assigned on the Admin tab.

B.

The Cisco IMC IP address needs to be in the same subnet as the management IP.

C.

The Cisco IMC needs to be upgraded to the same version as the UCS Manager.

D.

The server needs to be fully discovered.

 

Correct Answer: AD

 

 

QUESTION 82

A customer is configuring SAN pin groups in a Cisco UCS domain. The customer notices that pinning is not working and traffic from the vHBA is not passing over the Fibre Channel uplink port. Wh
ich of these must be done for pinning to work correctly?

 

A.

Include the SAN pin group in a vHBA policy and then include the vHBA policy in the service profile

that is assigned to that server.

B.

Include the SAN policy in the Cisco UCS Manager to match with pin groups on the fabric interconnect.

C.

The customer must have Cisco UCS Manager version 2.0 or above.

D.

Fibre Channel switch mode needs to be configured first.

 

Correct Answer: A

 

QUESTION 83

Which option is the cause when a DIMM is marked as bad?

 

A.

More than 16000 errors were witnessed during test execution during BIOS.

B.

DIMM Blacklisting is enabled.

C.

The DIMM is missing.

D.

The bank of DIMMs is composed of different size DIMMs.

 

Correct Answer: A

 

QUESTION 84

Refer to exhibit. A Cisco UCS admin is troubleshooting an issue with a vNIC not coming up on a blade. When looking at the CLI of the “Fabric Interconnect”,the admin runs this command to view the status of the interface. Which option describes a possible reason why the interface is stuck in an “initializing” state?

 

clip_image001

 

A.

The service profile is not applied to a blade.

B.

The VLANs defined on the vNIC are not defined on a matching uplink port.

C.

The uplink port is down.

D.

The QoS policy on the vNIC is invalid.

E.

The MTU on the vNIC is higher than the MTU configured in the QoS system class.

 

Correct Answer: C

 

 

QUESTION 85

Which two options are causes for failure of a Cisco C-Series server that is configured to boot from SAN? (Choose two.)

 

A.

The boot LUN ID is not 0.

B.

The ISCSI target is only available via one via one path through the network.

C.

C-Series does not support boot from SAN.

D.

The KVM dongle is attached to the front of the server with a USB stick installed.

E.

Under the FCoE properties on the vNIC adapter, the FCoE VLAN ID is set to 10.

F.

The boot table for fc0 has not been configured.

 

Correct Answer: DF

 

 

 

 

 

QUESTION 86

Which command on the Fabric Interconnect displays packet statistics for a given QoS group and MTU size?

 

A.

show policy-map interface ethernet x/y

B.

show queuing interface ethernet x/y

C.

show interface ethernet x/y

D.

show class-map type qos

E.

show interface queuing ethernet x/y

 

Correct Answer: B

 

 

QUESTION 87

A Cisco UCS admin is trying to integrate Cisco UCS Manager with Active Directory Authentication. After the configuration is done, the admin is still unable to log in using LDAP credentials. When running a debug on the Fabric Interconnect, this error is displayed:

 

ldap_build_roles_and_locales_from_attr: No attr for usr profile

 

Which step was missed in the configuration?

 

A.

The LDAP provider was not configured correctly.

B.

The proper RBAC role(s) were not assigned to the user.

C.

Cisco UCS Manager 2.1 is required for LDAP integration.

D.

The “Attribute” field in Cisco UCS was left blank.

 

Correct Answer: B

 

 

QUESTION 88

Which three requirements are needed to configure a blade to boot successfully from Fibre Channel? (Choose three.)

 

A.

zoning

B.

LUN masking

C.

WWPN device alias

D.

boot from SAN policy

E.

SAN connectivity policy

F.

port assignment

G.

target WWPN needs to be set in the boot from SAN policy

 

Correct Answer: ABD

 

 

QUESTION 89

Which description of a core file is true?

 

A.

It is generated by a system failure.

B.

It is generated by a process failure.

C.

It is generated by a component failure.

D.

It is generated by a hardware failure.

 

Correct Answer: B

 

 

QUESTION 90

Which logs are used to troubleshoot hardware failure?

 

A.

system event log

B.

audit log

C.

accounting log

D.

gateway logs

E.

system log

 

Correct Answer: A

 

Free VCE & PDF File for Cisco 642-035 Exam Questions

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …