[Free] Download New Updated (December) Cisco 350-080 Exam Questions 201-210

Ensurepass

QUESTION 201

Which PIM mode is supported in Cisco NX-OS?

 

A.

sparse mode

B.

dense mode

C.

sparse-dense mode

D.

dense-sparse mode

 

Correct Answer: A

 

 

QUESTION 202

Refer to the exhibit. Which configuration command (or commands) will produce the output that is shown in the exhibit?

 

clip_image002

 

A.

no feature igmp

B.

no feature igmp snooping

C.

vlan 201

no ip igmp snooping

D.

vlan configuration 201

no ip igmp snooping

E.

interface vlan 201

no ip igmp snooping

 

Correct Answer: D

 

 

QUESTION 203

Refer to the exhibit. The following message output was displayed while configuring PIM on Nexus 7000. Which command should be configured on the Cisco Nexus 7000 Series switch to allow the desired configuration?

 

clip_image004

 

A.

feature multicast

B.

feature pim

C.

ip multicast-routing

D.

ip pim routing

 

Correct Answer: B

 

 

QUESTION 204

Refer to the exhibit. When the engineer tried to check CoPP on the switch, the engineer observed the error that is shown in the exhibit. Which option describes the reason for the displayed output?

 

clip_image006

 

A.

The Cisco NX-OS version that is running does not support CoPP.

B.

The CoPP feature is not enabled on this switch.

C.

The CoPP CLI is available from the default VDC.

D.

CoPP is enabled by default but not configured.

 

Correct Answer: C

 

 

QUESTION 205

How many ACL capture sessions can be configured on a Cisco Nexus 7000 switch?

 

A.

ACL capture is not supported on the Cisco Nexus 7000 switch.

B.

Only one ACL capture session can be active at any given time in the system across virtual device contexts.

C.

Only one ACL capture session can be active in each virtual device context.

D.

The number of ACL capture sessions depends on the space that is available within the ACL Ternary Content Addressable Memory.

E.

Only one ACL capture session is supported per VLAN.

 

Correct Answer: B

 

 

QUESTION 206

On a Cisco Nexus 7000 device, on which port type can port security be configured?

 

A.

Access ports

B.

SPAN destination port

C.

trunk ports

D.

public VLAN-enabled ports

 

Correct Answer: A

 

 

QUESTION 207

Which statement is true about DHCP snooping on the Cisco Nexus 7000 platform?

 

A.

DHCP snooping cannot be enabled globally and on a per-VLAN basis.

B.

By default, DHCP snooping is disabled globally and on all VLANs.

C.

You can enable DHCP snooping on a single VLAN only.

D.

For DHCP snooping to function properly, all DHCP servers must be connected to the device through untrusted interfaces.

 

Correct Answer: B

 

 

QUESTION 208

Which two statements about VDC configuration and limitations are true? (Choose two.)

 

A.

Standard VDCs cannot share interfaces, VLANs, or VRF tables.

B.

Any user can create VDCs.

C.

Only the network administrator role can use the switchto vdc command.

D.

After a network administrator uses the switchto vdc command, the network administrator becomes a VDC administrator for the new VDC.

E.

There is no CLI command to return to the original VDC.

 

Correct Answer: AD

 

 

QUESTION 209

Refer to the exhibit. You configured a port on a Cisco Nexus 7000 switch as a trunk port. Which VLANs are allowed on the trunk port based on the port configuration in the exhibit?

 

clip_image008

 

A.

No VLANs are allowed by default. Use the switchport trunk allowed vlan 1-4094 command to allow all VLANs.

B.

Only Native VLAN 1 will be allowed.

C.

VLANs 1 to 3967, and 4048 to 4094 are allowed.

D.

VLANs 1 to 3900, and 4048 to 4094 are allowed.

E.

VLANs 1 to 4094 are allowed.

 

Correct Answer: C

 

 

QUESTION 210

Which three prerequisites must be met before configuring FabricPath on a Cisco Nexus 7000 switch? (Choose three.)

 

A.

Ensure that the Enhanced Layer 2 license is installed on the switch.

B.

The FabricPath feature set must be installed on the default and non-default VDCs.

C.

Spanning tree must be disabled on the switch.

D.

Ensure that you are working on the F Series module.

E.

Ensure that you are working on the M Series module.

F.

The FabricPath feature set must be installed only on the default VDC.

 

Correct Answer: ABD

 

Free VCE & PDF File for Cisco 350-080 Exam Questions

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …