[Free] 2019(Nov) EnsurePass Cisco 100-105 Dumps with VCE and PDF 211-220

Get Full Version of the Exam
http://www.EnsurePass.com/100-105.html

Question No.211

Which device allows users to connect to the network using a single or double radio?

  1. access point

  2. switch

  3. wireless controller

  4. firewall

Correct Answer: A

Question No.212

Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?

  1. IP routing must be enabled to allow the two hosts to communicate.

  2. The two hosts are in the same broadcast domain.

  3. The switch must be configured with a VLAN to allow the two hosts to communicate.

  4. Port security prevents the hosts from connecting to the switch.

Correct Answer: B

Explanation:

http://www.cisco.com/c/en/us/support/docs/lan-switching/inter-vlan- routing/41860-howto-L3- intervlanrouting.html

Question No.213

Which NTP command configures the local device as an NTP reference clock source?

  1. ntp peer

  2. ntp broadcast

  3. ntp master

  4. ntp server

Correct Answer: D

Question No.214

Which routing protocol has the smallest default administrative distance?

  1. IBGP

  2. OSPF

  3. IS-IS

  4. EIGRP

  5. RIP

    Correct Answer: D

    Explanation:

    http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/15986-admin- distance.html

    Default Distance Value TableThis table lists the administrative distance default values of the protocols that Cisco supports:

    Route Source

    Default Distance Values Connected interface

    0

    Static route 1

    Enhanced Interior Gateway Routing Protocol (EIGRP) 5

    summary route External Border Gateway Protocol (BGP) 20

    Internal EIGRP 90

    IGRP 100 OSPF 110

    Intermediate System-to-Intermediate System (IS-IS) 115

    Routing Information Protocol (RIP) 120

    Exterior Gateway Protocol (EGP) 140

    On Demand Routing (ODR) 160

    External EIGRP 170

    Internal BGP 200

    Unknown* 255

    Question No.215

    Which statement about static routes is true?

    1. The source interface can be configured to make routing decisions.

    2. A subnet mask is entered for the next-hop address.

    3. The subnet mask is 255.255 255.0 by default

    4. The exit interface can be specified to indicate where the packets will be routed.

Correct Answer: D

Explanation:

Static routing can be used to define an exit point from a router when no other routes are available or necessary. This is called a default route.

Question No.216

By default, how many MAC addresses are permitted to be learned on a switch port with port security enabled?

A.

8

B.

2

C.

1

D.

0

Correct Answer: C

Question No.217

Which statement about a router on a stick is true?

  1. Its date plane router traffic for a single VI AN over two or more switches.

  2. It uses multiple subinterfaces of a single interface to encapsulate traffic for different VLANs on the same subnet.

  3. It requires the native VLAN to be disabled.

  4. It uses multiple subinterfaces of a single interface to encapsulate traffic for different VLANs.

Correct Answer: D

Explanation:

https://www.freeccnaworkbook.com/workbooks/ccna/configuring-inter-vlan-routing-router-on-a- stick

Question No.218

Which network topology allows all traffic to flow through a central hub?

  1. bus

  2. star

  3. mesh

  4. ring

Correct Answer: B

Question No.219

Which NAT type is used to translate a single inside address to a single outside address?

  1. dynamic NAT

  2. NAT overload

  3. PAT

  4. static NAT

Correct Answer: D

Explanation:

Network address translation (NAT) is the process of modifying IP address information in IP packet headers while in transit across a traffic routing device.

There are two different types of NAT:

image

image

NAT PAT

Question No.220

What is the default lease time for a DHCP binding?

  1. 24 hours

  2. 12 hours

  3. 48 hours

  4. 36 hours

Correct Answer: A

Explanation:

By default, each IP address assigned by a DHCP Server comes with a one- day lease, which is

the amount of time that the address is valid. To change the lease value for an IP address, use the following command in DHCP pool configuration mode.

>

Get Full Version of the Exam
100-105 Dumps
100-105 VCE and PDF

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.