Download New Updated (Spring 2015) Cisco 350-001 Actual Tests 281-290

Ensurepass

 

QUESTION 281

Two BGP peers connected through a routed firewall are unable to establish a peering relationship. What could be the most likely cause?

 

A.       BGP peers must be Layer 2-adjacent.

B.       EBGP multihop is not configured.

C.       The firewall is not configured to allow IP protocol 89.

D.      The firewall is not configured to allow UDP 179.

 

Correct Answer: B

 

 

QUESTION 282

Which two of these steps are minimum requirements to configure OSPFv3 under IPv6? (Choose two.)

 

A.       Configure a routing process using the command ipv6 router ospf [process-id].

B.       Add the network statement for the interfaces on which OSPF will run.

C.       Configure OSPF on the interface that it will run on.

D.      Use the passive-interface command on the interfaces on which OSPF should not run.

E.       Enable routing.

 

Correct Answer: CE

 

 

QUESTION 283

You add the following commands into a routed topology: router eigrp 1 variance 3 traffic-share min across- interfaces. Users now complain about voice quality in your VoIP system. What should be done?

 

A.       Add the command: router eigrp 1 traffic-share voice interface fast 0/0.

B.       Reconfigure EIGRP to recognize voice packets.

C.       Remove the variance from the configuration.

D.      Reconfigure the VoIP system to use RTP sequence number headers.

E.       Use an H.323 gatekeeper for your VoIP system to negotiate an H.245 uneven packet buffer.

F.        Reconfigure EIGRP to version 2.

 

Correct Answer: C

 

 

 

 

 

 

QUESTION 284

Refer to the exhibit. How would you get the 1.1.1.1 network into the OSPF database?

 

clip_image001

 

A.       Configure RTA as an ASBR.

B.       Redistribute connected routes on RTA into OSPF.

C.       Set up a virtual link between area 1 and area 0.

D.      Set up a virtual link between area 1 and area 2.

E.       Add a static route into RTB and enter it into OSPF.

F.        Place a network 1.1.1.0 0.0.0.0 command into RTB.

G.      Set up a unique router ID on RTA using an RFC 1918 address.

H.      Change area 0 on RTB to area 1.

 

Correct Answer: C

 

 

QUESTION 285

Refer to the exhibit. Router E learned about the PIM RP (designated as 7.7.7.7) from four different sources. Routers A and D advertised the 7.0.0.0 network via EIGRP. Routers B and C advertised the 7.0.0.0 network via OSPF. Considering that all four Ethernet interfaces on router E could potentially lead back to the PIM-RP, when router E receives the first multicast packet down the shared tree, which incoming interface will be used to successfully pass the RPF check?

 

clip_image002

 

A.  E0

B.  E1

C.  E2

D.  E3

E.  None of these interfaces will be used to successfully pass the RPF check.

F.  All of these interfaces would successfully pass the RPF check.

 

Correct Answer: A

 

 

QUESTION 286

Refer to the exhibit. From the MAC addresses shown in the command output, to which two ports is the multicast stream 225.230.57.199 being forwarded on this switch? (Choose two.)

 

Switch#show mac- address-table multicast

 

clip_image004

 

A.       Fa6/28

B.       Fa7/20

C.       Gi3/7

D.      Fa4/2

E.       Fa4/14

F.        Fa4/38

G.      Fa6/28

H.      Fa5/7

 

Correct Answer: CE

 

 

QUESTION 287

Refer to the exhibit. Two ISPs have decided to use MSDP and configured routers X and Y (both are PIM RPs) as MSDP peers. In the domain of ISP B, PC A has sent an IGMP membership report for the group 224.1.1.1 and PC B has sent an IGMP membership report for the group 224.5.5.5. Assuming that the MSDP peering relationship between routers X and Y is functional, and given the partial configuration output shown from router X, which two of these statements are true? Choose two.)

 

clip_image005

 

A.       Router X will contain an entry for 224.1.1.1 in its SA cache and will also have an installed (S, G) entry for this in its mroute table.

B.       Router X will not contain an entry for 224.1.1.1 in its SA cache but will have an installed (*, G) entry for this in its mroute table.

C.       Router X will not contain an entry for 224.5.5.5 in its SA cache but will have an installed (S, G) entry for this in its mroute table.

D.       Router X will not contain an entry for 224.5.5.5 in its SA cache but will have an installed (*, G) entry for this in its mroute table.

E.        Router X will have no entries for 224.5.5.5 in neither its SA cache nor in its mroute table.

F.        Router X will have no entries for 224.1.1.1 in neither its SA cache nor in its mroute table.

 

Correct Answer: AD

 

 

QUESTION 288

You are about to migrate a customer network to use a VSS. Which of these statements is true about a VSS?

 

A.       The VSS switch must be the root bridge for all VLANs and is automatically designated.

B.       The VSS switch is defined in RFC 4318 as a managed object.

C.       The PAgP+ or LACP protocols are used to maintain the operational state of the VSS devices.

D.      A VSS interope
rates with a virtual port channel.

E.       The 802.1 Q or ISL protocols are used to maintain the operational state of the VSS devices.

F.        A VSS increases the size of the spanning-tree domain.

 

Correct Answer: C

 

 

QUESTION 289

You have done a partial migration from 802.1D STP to 802.1w STP. Which of the following is true?

 

A.       802.1 D and 802.1w intemperate only when the 802.1 D STP domain supports rapid convergence.

B.       Ports leading to 802.1D devices will run in compatibility mode, while the rest of the ports will run in 802.1w mode.

C.       This is an invalid configuration and a partial migration cannot be done.

D.       The bridge timers will be set to match the 802.1 D devices.

E.        A secondary root bridge will always be populated within the 802.1 D domain.

F.        If the root bridge is selected within the 802.1 D domain, the whole STP domain will run in 802.1 D compatibility mode.

G.       In partially migrated 802.1w networks, it is recommended to keep the STP diameter below 4.

 

Correct Answer: B

 

 

QUESTION 290

The network administrator is trying to add Switch1 to the network, but the 802.1 Q trunk is not coming up. Switch1 was previously tested in the laboratory and its trunk configuration worked fine. What are three possible causes of this problem? (Choose three.)

 

A.       The trunking configuration mode on Switch1 is set to Off.

B.       The trunking configuration mode on the other end is set to On.

C.       The trunking configuration mode on the other end is set to Desirable.

D.      Cisco Discovery Protocol is not running on the other end.

E.       There is a VTP domain name mismatch.

F.        Switch1 does not support 802.1Q.

 

Correct Answer: BCE

 

Free VCE & PDF File for Cisco 350-001 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …