Download New Updated (Spring 2015) Cisco 200-101 Actual Tests 91-100

Ensurepass

 

QUESTION 91

What command is used to verify the DLCI destination address in a Frame Relay static configuration?

 

A.      show frame-relay pvc

B.      show frame-relay lmi

C.      show frame-relay map

D.      show frame relay end-to-end

 

Correct Answer: C

 

 

QUESTION 92

The output of the show frame-relay pvc command shows “PVC STATUS = INACTIVE”. What does this mean?

 

A.      The PVC is configured correctly and is operating normally, but no data packets have been detected for more than five minutes.

B.      The PVC is configured correctly, is operating no
rmally, and is no longer actively seeking the address of the remote router.

C.      The PVC is configured correctly, is operating normally, and is waiting for interesting traffic to trigger a call to the remote router.

D.      The PVC is configured correctly on the local switch, but there is a problem on the remote end of the PVC.

E.       The PVC is not configured on the local switch.

 

Correct Answer: D

 

 

QUESTION 93

Refer to the exhibit. A technician pastes the configurations in the exhibit into the two new routers shown. Otherwise, the routers are configured with their default configurations. A ping from Host1 to Host2 fails, but the technician is able to ping the S0/0 interface of R2 from Host1. The configurations of the hosts have been verified as correct. What is the cause of the problem?

 

clip_image002

 

A.      The serial cable on R1 needs to be replaced.

B.      The interfaces on R2 are not configured properly.

C.      R1 has no route to the 192.168.1.128 network.

D.      The IP addressing scheme has overlapping subnetworks.

E.       The ip subnet-zero command must be configured on both routers.

 

Correct Answer: C

 

 

QUESTION 94

What does the frame-relay interface-dlci command configure?

 

A.      local DLCI on the subinterface

B.      remote DLCI on the main interface

C.      remote DCLI on the subinterface

D.      local DLCI on the main interface

 

Correct Answer: A

 

 

QUESTION 95

Refer to the exhibit. The show interfaces serial 0/1 command was issued on the R10-1 router. Based on the output displayed which statement is correct?

 

clip_image004

 

A.      The cable connected to the serial 0/1 interface of the R10-1 router is a DTE cable.

B.      The R10-1 router can ping the router interface connected to the serial 0/1 interface.

C.      The clock rate used for interface serial 0/1 of the R10-1 router is 1,544,000 bits per second.

D.      The CSU used with the serial 0/1 interface of the R10-1 router has lost connection to the service provider.

E.       The interface of the remote router connected to the serial 0/1 interface of the R10-1 router is using the default serial interface encapsulation.

 

Correct Answer: E

 

 

QUESTION 96

Refer to the exhibit. How should the FastEthernet0/1 ports on the 2950 model switches that are shown in the exhibit be configured to allow connectivity between all devices?

 

clip_image005

 

A.        The ports only need to be connected by a crossover cable.

 

B.        SwitchX (config)# interface fastethernet 0/1

SwitchX (config-if)# switchport mode access

SwitchX (config-if)# switchport access vlan 1

 

C.        SwitchX (config)# interface fastethernet 0/1

SwitchX (config-if)# switchport mode trunk

SwitchX (config-if)# switchport trunk vlan 1

SwitchX (config-if)# switchport trunk vlan 10

SwitchX (config-if)# switchport trunk vlan 20

 

D.        SwitchX(config)# interface fastethernet 0/1

SwitchX(config-if)# switchport mode trunk

 

Correct Answer: D

 

 

QUESTION 97

Refer to the exhibit. Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)

clip_image006

 

A.       Host E and host F use the same IP gateway address.

B.        Router1 and Switch2 should be connected via a crossover cable.

C.        Router1 will not play a role in communications between host A and host D.

D.       The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.

E.        Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.

F.        The FastEthernet 0/0 interface on Router1 and Switch2 trunk ports must be configured using the same encapsulation type.

 

Correct Answer: DF

 

 

QUESTION 98

A department decides to replace its hub with a Catalyst 2950 switch that is no longer needed by another department. To prepare the switch for installation, the network administrator has erased the startup configuration and reloaded the switch. However, PCs that are connected to the switch experience various connectivity problems. What is a possible cause of the problem?

 

A.       The VLAN database was not erased.

B.        The management VLAN is disabled.

C.        The running configuration should have been erased.

D.       The “mode” button was not pressed when the switch was reloaded.

E.        The switch was not configured with an IP address or a default gateway.

 

Correct Answer: A

 

 

QUESTION 99

Refer to the exhibit. Why has this switch not been elected the root bridge for VLAN1?

 

clip_image008

 

A.       It has more than one interface that is connected to the root network segment.

B.        It is running RSTP while the elected root bridge is running 802.1d spanning tree.

C.        It has a higher MAC address than the elected root bridge.

D.       It has a higher bridge ID than the elected root bridge.

 

Correct Answer: D

 

 

QUESTION 100

Refer to the exhibit. The following commands are executed on interface fa0/1 of 2950Switch.

 

2950Switch(config-if)# switchport port-security

2950Switch(config-if)# switchport port-security mac-address sticky

2950Switch(config-if)# switchport port-security maximum 1

 

The Ethernet frame that is shown arrives on interface fa0/1. What two functions will occur when this frame is received by 2950Switch? (Choose two.)

 

clip_image010

 

A.       The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF.

B.        Only host A will be allowed to transmit frames on fa0/1.

C.        This frame will be discarded when it is received by 2950Switch.

D.       All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1.

E.        Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded out fa0/1.

F.        Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded out fa0/1.

 

Correct Answer: BD

 

Free VCE & PDF File for Cisco 200-101 Real Exam

Instant Access to Free VCE Files: CCNA | CCNP | CCIE …
Instant Access to Free PDF Files: CCNA | CCNP | CCIE …