Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 261-270

Ensurepass   QUESTION 261 Refer to the exhibit. The output that is shown is generated at a switch. Which three of these statements are true? (Choose three.)     A.       All ports will be in a state of discarding, learning or forwarding. B.       Thirty VLANs have been configured on this switch. C.       The bridge priority is lower than the default value for spanning tree. D.       Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 241-250

Ensurepass  QUESTION 241 Which switch would STP choose to become the root bridge in the selection process?   A.        32768: 11-22-33-44-55-66 B.        32768: 22-33-44-55-66-77 C.        32769: 11-22-33-44-55-65 D.        32769: 22-33-44-55-66-78   Correct Answer: A     QUESTION 242 A company implements video conferencing over IP on Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 251-260

Ensurepass  QUESTION 251 A Catalyst 2950 needs to be reconfigured. What steps will ensure that the old configuration is erased? (Choose three.)   A.        Erase flash. B.        Restart the switch. C.        Delete the VLAN database. D.        Erase the running configuration. E.         Erase the startup configuration. Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 221-230

Ensurepass  QUESTION 221 Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two)   A.        Router(config)#router ospf 1 B.        Router(config)#router ospf 0 C.        Router(config)#router ospf area 0 D.        Router(config-router)#network 192.168.16.0 0.0.0.255 area Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 231-240

Ensurepass     QUESTION 231 A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?     A.        The OSPF area is not configured properly. B.        Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 211-220

Ensurepass  QUESTION 211 A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?   A.       the OSPF route B.       the EIGRP route C.       Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 191-200

Ensurepass   QUESTION 191 Which of the following are true regarding the debug output shown in the graphic? (Choose Two)     A.     This router was configured with the commands: RtrA(config)#router rip RtrA(config-router)#version 2 RtrA(config-router)#network 172.16.0.0 RtrA(config-router)#network 10.0.0.0   B.     This router was configured with the commands: RtrA(config)#router rip RtrA(config-router)#network 172.16.0.0 RtrA(config-router)#network Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 201-210

Ensurepass  QUESTION 201 OSPF routing uses the concept of areas. What are the characteristics of OSPF areas? (Choose three.)   A.       Each OSPF area requires a loopback interface to be configured. B.       Areas may be assigned any number from 0 to 65535. C.       Area 0 is called the backbone area. D.       Hierarchical OSPF networks do not require multiple areas. E.        Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 171-180

Ensurepass    QUESTION 171 Use the output from the router shown in the graphic above to determine which of the following are correct. (Choose two.)     A.        Router John uses a link-state routing protocol. B.        Router John will receive routing updates on the Serial0/0 interface. C.        Router John will receive routing updates on the Serial0/1 interface. D.        Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 181-190

Ensurepass   QUESTION 181 What is the default routing update period for RIPv2?   A.       15 seconds B.       30 seconds C.       180 seconds D.       240 seconds Correct Answer: B     QUESTION 182 Refer to the exhibit. S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology. While testing this Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 161-170

Ensurepass  QUESTION 161 Refer to the exhibit. The network administrator must establish a route by which London workstations can forward traffic to the Manchester workstations. What is the simplest way to accomplish this?     A.       Configure a dynamic routing protocol on London to advertise all routes to Manchester. B.       Configure a dynamic routing protocol on London to advertise summarized routes to Manchester. C.       Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 151-160

Ensurepass  QUESTION 151 In the implementation of VLSM techniques on a network using a single Class C IP address, which subnet mask is the most efficient for point-to-point serial links?   A.        255.255.255.240 B.        255.255.255.254 C.        255.255.255.252 D.        255.255.255.0 E.         255.255.255.248 Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 141-150

Ensurepass  QUESTION 141 Which of the following IP addresses can be assigned to the host devices? (Choose two.)   A.        205.7.8.32/27 B.        191.168.10.2/23 C.        127.0.0.1 D.        224.0.0.10 E.         203.123.45.47/28 F.         10.10.0.0/13   Correct Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 121-130

Ensurepass  QUESTION 121 The ip subnet zero command is not configured on a router. What would be the IP address of Ethernet0/0 using the first available address from the sixth subnet of the network 192.168.8.0/29?   A.        192.168.8.25 B.        192.168.8.41 C.        192.168.8.49 D.        192.168.8.113   Correct Answer: C     QUESTION Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 131-140

Ensurepass  QUESTION 131 Which of the following host addresses are members of networks that can be routed across the public Internet? (Choose Three.)   A.        10.172.13.65 B.        172.16.223.125 C.        172.64.12.29 D.        192.168.23.252 E.         198.234.12.95 F.         Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 101-110

Ensurepass    QUESTION 101   Including the address on the Routed Ethernet interface, how many hosts can have IP addresses on the LAN to which Routed is connected?   A.      6 B.      30 C.      62 D.      126   Correct Answer: A                                           Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 111-120

Ensurepass    QUESTION 111 Refer to the exhibit. Which three statements correctly describe Network Device A? (Choose three.)     A.       With a network wide mask of 255.255.255.128, each interface does not require an IP address. B.       With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet. C.       With a network wide mask of 255.255.255.0, Read more [...]

Download New Updated (Spring 2015) Cisco 100-101 Actual Tests 91-100

Ensurepass  QUESTION 91 Refer to the exhibit. The junior network support staff provided the diagram as a recommended configuration for the first phase of a four-phase network expansion project. The entire network expansion will have over 1000 users on 14 network segments and has been allocated this IP address space.   192.168.1.1 through 192.168.5.255 192.168.100.1 through 192.168.100.255   What are three problems with this design? (Choose three.)     A.      Read more [...]