2013 Latest 642-902 Pass4sure Free Tests 271-280

Ensurepass

 

QUESTION 271

When policy-based routing (PBR) is being configured, which three criteria can the set command specify? (Choose three.)

 

A.  all interfaces through which the packets can be routed

B.  all interfaces in the path toward the destination

C.  adjacent next hop router in the path toward the destination

D.  all routers in the path toward the destination

E.  all networks in the path toward the destination

F.  type of service and precedence in the IP packets

 

Answer: ACF

 

 

QUESTION 272

Refer to the Exhibit. What is the correct configuration to enable router P4 to exchange RIP routing updates with router P1 but not with router P3?

clip_image001

 

A.  P4(Config)# interface fa0/0

    P4(Config-if)# neighbor 192.168.10.3

    P4(config-if)# passive-interface fa0/0

 

B.  P4(config)# router rip

    P4(config-router)#neighbor 192.168.10.3

    P4(Config-router)#passive-interface fa0/0

 

C.  P4(config)# interface fa0/0

    P4(config-if)# neighbor 192.168.10.3

    P4(config-if)# passive interface192.168.10.34

 

D.  P4(config)# router rip

    P4(config-router)# neighbor 162.168.10.34 no broadcast

    P4(config-router)# passive-interface fa0/0

 

Answer: B

 

 

QUESTION 273

Which BGP feature should be used to avoid high memory utilization on a router?

 

A.       soft-reconfiguration

B.       route refresh

C.       BGP communities

D.      full-mesh BGP peering

 

Answer: B

 

 

QUESTION 274

What is a key benefit of using a GRE tunnel to provide connectivity between branch offices and headquarters?

 

A.       authentication, integrity checking, and confidentiality

B.       less overhead

C.       dynamic routing over the tunnel

D.      granular QoS support

E.       open standard

F.        scalability

 

Answer: C

 

 

QUESTION 275

Which DSL encapsulation method requires client software running on the end-user PC that is directly connected to a DSL modem?

 

A.      PPPoA

B.      PPPoE

C.      PPP

D.      L2TP

E.       ATM

 

Answer: B

 

 

QUESTION 276

Refer to the exhibit.

clip_image002

clip_image003

 

A new TAC engineer came to you for advice. A GRE over IPsec tunnel was configured, but the tunnel is not coming up. What did the TAC engineer configure incorrectly?

 

A.       The crypto isakmp configuration is not correct.

B.       The crypto map configuration is not correct.

C.       The network 172.16.1.0 is not included in the OSPF process.

D.      The interface tunnel configuration is not correct.

 

Answer: A

 

 

 

QUESTION 277

Refer to the exhibit. ROUTE.com is planning to implement a secure OSPF network to support traffic between clients on the 172.16.10.0/24 network and the file server on the 172.16.20./24 network. You have been asked to review the implementation and verification plans. Which statement about the plan is true?

clip_image004

 

A.       It is complete as written.

B.       It should include a task that verifies that the interarea routes are using the proper MED.

C.       The plan should include a task that verifies that load sharing is active on the appropriate links.

D.      The plan should include a task that verifies end-to-end connectivity between the clients and the file server.

 

Answer: D

 

 

QUESTION 278

Click and drag the BGP attribute characterization on the left to the correct BGP attribute on the right.

clip_image006

 

Answer:

clip_image008

 

 

QUESTION 279

What is the sequence, from first to last, that OSPF will follow when choosing a router ID?

 

A.  1. the highest IP address on any active loopback interface;

    2. The router-id command results;

    3.The highest IP address of any active physical interface.

 

B.  1. the highest IP address on any active loopback interface;

    2. The highest IP address of any active Physical interface;

    3. The router-id command result.

 

C.  1. The highest IP address of any active Physical interface;

    2. the highest IP address on any active loopback interface;

    3. The router-id command results.

 

D.  1. The highest IP address of any active Physical interface;

    2. The router-id command result;

    3.The highest IP address of any active physical interface.

E.  1. The router-id command results;

    2. The highest IP address of any active Physical interface;

    3. The highest IP address of any active physical interface.

 

F.  1. The router-id command result;

   2. The highest IP address on any active loopback interface;

   3. The highest IP address of any active physical interface.

 

Answer: F

 

 

QUESTION 280

Click the resources on the left that you need to create an implementation plan for an OSPF project and drag them to the target zone on the right.

clip_image010

 

Answer:

clip_image012

 

DownloadLatest 2013 642-902 Security Free Tests , help you to pass exam 100%.

 

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.