2013 Latest 642-832 Pass4sure Free Tests 31-40

Ensurepass

 

Ticket 5 : NAT ACL

QUESTION 31

Refer to the exhibit.

clip_image002

clip_image004

clip_image006

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

 

Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

 

A.       R1

B.       R2

C.       R3

D.      R4

E.       DSW1

F.        DSW2

G.      ASW1

 

Correct Answer: A

 

 

QUESTION 32

Refer to the exhibit.

clip_image007

clip_image008

clip_image006[1]

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

 

Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

 

A.       BGP

B.       NTP

C.       IP NAT

D.      IPv4 OSPF Routing

E.       IPv4 OSPF Redistribution

F.        IPv6 OSPF Routing

G.      IPv4 layer 3 security

 

Correct Answer: C

 

 

QUESTION 33

Refer to the exhibit.

clip_image007[1]

clip_image008[1]

clip_image009

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

 

Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

 

A.       Under the interface Serial0/0/0 configuration enter the ip nat inside command.

B.       Under the interface Serial0/0/0 configuration enter the ip nat outside command.

C.       Under the ip access-list standard nat_trafic configuration enter the permit 10.2.0.0 0.0.255.255 command.

D.      Under the ip access-list standard nat_trafic configuration enter the permit 209.65.200.0 0.0.0.255 command.

 

Correct Answer: C

 

 

Ticket 6 : R1 ACL

QUESTION 34

Refer to the exhibit.

clip_image010

clip_image011

clip_image009[1]

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

 

Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

 

A.       R1

B.       R2

C.       R3

D.      R4

E.       DSW1

F.        DSW2

G.      ASW1

 

Correct Answer: A

 

 

QUESTION 35

Refer to the exhibit.

clip_image010[1]

clip_image011[1]

clip_image009[2]

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

 

Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

 

A.       BGP

B.       NTP

C.       IP NAT

D.      IPv4 OSPF Routing

E.       IPv4 OSPF Redistribution

F.        IPv6 OSPF Routing

G.      IPv4 layer 3 security

 

Correct Answer: G

 

 

QUESTION 36

Refer to the exhibit.

clip_image010[2]

clip_image011[2]

clip_image009[3]

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

 

Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

 

A.       Under the interface Serial0/0/1 enter the ip access-group edge_security out command.

B.       Under the ip access-list extended edge_security configuration add the permit ip 209.65.200.224 0.0.0.3 any command.

C.       Under the ip access-list extended edge_security configuration delete the deny ip 10.0.0.0.0

A.       0.255.255.255 any command.

D.      Under the interface Serial0/0/0 configuration delete the ip access-group edge_security in command and enter the ip access-group edge_security out command.

 

Correct Answer: B

 

 

Ticket 7 : Port Security

QUESTION 37

Refer to the exhibit.

clip_image010[3]

clip_image011[3]

clip_image009[4]

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

 

Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

 

A.       R1

B.       R2

C.       R3

D.      R4

E.       DSW1

F.        DSW2

G.      ASW1

H.      ASW2

 

Correct Answer: G

 

 

QUESTION 38

Refer to the exhibit.

clip_image010[4]

clip_image011[4]

clip_image009[5]

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

 

Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

 

A.       NTP

B.       Switch-to-Switch Connectivity

C.       Access Vlans

D.      Port Security

E.       VLAN ACL / Port ACL

F.        Switch Virtual Interface

 

Correct Answer: D

 

 

QUESTION 39

Refer to the exhibit.

clip_image010[5]

clip_image011[5]

clip_image009[6]

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

 

Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

 

A.         In Configuration mode, using the interface range Fa1/0/1-2, then no switchport port-security interface configuration commands. Then in exec mode clear errdisable interface fa 1/01-2 vlan 10 command

B.         In Configuration mode, using the interface range Fa1/0/1-2, then no switchport port-security, followed by shutdown, no shutdown interface configuration commands.

C.         In Configuration mode, using the interface range Fa1/0/1-2, then no switchport port-security interface configuration commands.

D.         In Configuration mode, using the interface range Fa1/0/1-2, then no switchport port-security interface configuration commands. Then in exec mode clear errdisable interface fa 1/0/1, then clear errdisable interface fa 1/0/2 commands.

 

Correct Answer: B

 

 

Ticket 8 : Redistribution of EIGRP to OSPF

QUESTION 40

Refer to the exhibit.

clip_image010[6]

clip_image011[6]

clip_image009[7]

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

 

Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

 

A.       R1

B.       R2

C.       R3

D.      R4

E.       DSW1

F.        DSW2

G.      ASW1

H.      ASW2

 

Correct Answer: D

 

DownloadLatest 2013 642-832 Free Tests , help you to pass exam 100%.

 

 

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.