Refer to the shown below.
what statement is correct regarding the output shown in the graphic?
A. These two log messages will not have severity level. They are not errors but are just informational messages.
B. The first log message is categorized as a warning message.
C. These messages regarding interface status are normal output and will always be displayed when you exit config mode.
D. The first log message is an error message with a severity level of 3.
E. The second message would be shown if the logging console warning command had been issued.
Correct Answer: D
Refer to the configuration statements shown in the graphic above.
Which statement reflects what the effect is of this configuration sequence?
A. These commands will generate an error message because you cannot use an access list with any debug commands.
B. These commands will have no effect at all. The debug ip packet command will work as normal and display info for all IP packets.
C. These commands turn on debug ip packet only for packets between hosts 10.1.1.1 and 172.16.1.1.
D. These commands will only work when you specify only one host rather than two.
Correct Answer: C
What is the result if you configure two devices with the ntp server command?
A. Nothing will happen until one of the devices is configured with the prefer parameter.
B. The NTP protocol will determine which server is most reliable and will synchronize to that server.
C. The device with the highest priority will become the active server and the other device will become the backup server.
D. The device with the lowest MAC address will become the active server and the other device will become the backup server.
Correct Answer: B
A technician is troubleshooting connectivity problems between two routers that are directly connected through a serial line. The technician notices that the serial line is up, but cannot see any neighbors displayed in the output of the show cdp neighbors command. In which OSI layer is the problem most likely occurring?
B. data link
Correct Answer: B
What are two approaches to maintaining a network?(Choose two)
C. bottoms up
Correct Answer: BD
FCAPS is a network maintenance model defined by ISO. FCAPS stands for:
There are many Network Maintenance models. Match the model names on the left to the options on the right:
Match the items on the left to their purpose on the right:
– Client Should have IP 10.2.1.3
– EIGRP 100 is running between switch DSW1 & DSW2
– OSPF (Process ID 1) is running between R1, R2, R3, R4
– Network of OSPF is redistributed in EIGRP
– BGP 65001 is configured on R1 with Webserver cloud AS 65002
– HSRP is running between DSW1 & DSW2 Switches
The company has created the test bed shown in the layer 2 and layer 3 topology exhibits. This network consists of four routers, two layer 3 switches and two layer 2 switches.
In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.
DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary. R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISP’s network. Because the company’s address space is in the private range.
R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (184.108.40.206/24) network.
ASW1 and ASW2 are layer 2 switches.
NTP is enabled on all devices with 220.127.116.11 serving as the master clock source.
The client workstations receive their IP address and default gateway via R4’s DHCP server.
The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.
In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6. DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.
The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistribution is enabled where necessary.
Recently the implementation group has been using the test bed to do a `proof-of-concept’ on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.
Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.
Each ticket has 3 sub questions that need to be answered & topology remains same.
Question-1 Fault is found on which device,
Question-2 Fault condition is related to,
Question-3 What exact problem is seen & what needs to be done for solution
Ticket 1 : Switch Port Trunk
Refer to the exhibit.
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 18.104.22.168. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been operated indicating that Client 1 cannot ping the 22.214.171.124 address.
Use the supported commands to Isolated the cause of this fault and answer the following questions. On which device is the fault condition located?
Correct Answer: G
Refer to the exhibit.
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 126.96.36.199. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been opened indicating that Client 1 cannot ping the 188.8.131.52 address.
Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?
B. Switch-to-Switch Connectivity
C. Access Vlans
D. Port Security
E. VLAN ACL / Port ACL
F. Switch Virtual Interface
Correct Answer: B
DownloadLatest 2013 642-832 Free Tests , help you to pass exam 100%.