Which two statements are characteristics of a distance vector routing protocol? (Choose two)
A. RIP is an example of distance vector routing protocols.
B. Updates are periodic and include the entire routing table.
C. Routing updates are sent only after topology changes
D. The protocol can be useful in hub-and-spoke and hierarchical networks.
E. Convergence is usually faster than with link state protocols
F. Each router has its own view of the topology
Which of the following are true regarding the debug output shown in the graphic? (Choose Two)
A. This router was configured with the commands:
B. This router was configured with the commands:
C. Network 10.0.0.0 will be displayed in the routing table.
D. Network 192.168.168.0 will be displayed in the routing table.
E. This router was configured with the commands:
F. split-horizon was disabled on this router.
Which parameter can be tuned to affect the selection of a static route as a backup when a dynamic protocol is also being used?
A. link bandwidth
B. hop count
C. link cost
D. administrative distance
E. link delay
Which statement is true, as relates to classful or classless routing?
A. RIPV1 and OSPF are classless routing protocols.
B. Classful routing protocols send the subnet mask in routing updates.
C. Automatic summarization at classful boundaries can cause problems on discontigous networks.
D. EIGRP and OSPF are classful routing protocols and summarize routes by default.
The speed of all serial links is E1 and the speed of the all other links is 100Mb/s. A static route will be established on the Manchester router to direct traffic toward to the internet over the most direct path available. What configuration of the Manchester router will establish a route toward to the internet for traffic from workstation on the Manchester LAN?
A. ip route 0.0.0.0 255.255.255.0 172.16.100.2
B. ip route 0.0.0.0 255.255.255.252 22.214.171.124
C. ip route 0.0.0.0 0.0.0.0 126.96.36.199
D. ip route 0.0.0.0 0.0.0.0 172.16.100.1
E. ip route 0.0.0.0 255.255.255.255 172.16.100.2
F. ip route 0.0.0.0 0.0.0.0 172.16.100.2
Which two are advantages of static routing when compared to dynamic routing? (Choose two)
A. Security increases because only the network administrator may change the routing tables.
B. Configuration complexity decreases as network size increases.
C. Routing updates are automatically sent to neighbors.
D. Route summarization is computed automatically by the router.
E. Routing traffic load is reduced when used in stub network links
F. An efficient algorithm is used to build routing tables, using automatic updates. G. Routing tables adapt automatically to topology changes.
Refer to the exhibit:
What will Router1 do when it receives the data frame shown? (Choose three.)
A. Router1 will strip off the source MAC address and replace it with the MAC address 0000.0c36.6965.
B. Router1 will strip off the source IP address and replace it with the IP address 192.168.40.1.
C. Router1 will strip off the destination MAC address and replace it with the MAC address
D. Router1 will strip off the destination IP address and replace it with the IP address of 192.168.40.1.
E. Router1 will forward the data packet out interface FastEthernet0/1.
F. Router1 will forward the data packet out interface FastEthernet0/2.
Refer to the exhibit:
A packet with a source IP address of 192.168.2.4 and a destination IP address of 10.1.1.4 arrives at the
Hokes B router. What action does the router take?
A. forwards the received packet out the Serial0/0 interface
B. forwards a packet containing an EIGRP advertisement out the Serial0/1 interface
C. forwards a packet containing an ICMP message out the FastEthernet0/0 interface
D. forwards a packet containing an ARP request out the FastEthernet0/1 interface
Refer to the exhibit:
Router A has interfaces with addresses 192.168.1.1 and 172.16.1.1.Router B,which is connected to router A over a serial link, has interfaces with address 172.16.1.2 and 10.1.1.2. Which sequence of commands will configure RIPv2 on router B?
Refer to the graphic:
A static route to the 10.5.6.0/24 network is to be configured on the HFD router. Which commands will accomplish this? (Choose two.)
A. HFD(config)# ip route 10.5.6.0 0.0.0.255 fa0/0
B. HFD(config)# ip route 10.5.6.0 0.0.0.255 10.5.4.6
C. HFD(config)# ip route 10.5.6.0 255.255.255.0 fa0/0
D. HFD(config)# ip route 10.5.6.0 255.255.255.0 10.5.4.6
E. HFD(config)# ip route 10.5.4.6 0.0.0.255 10.5.6.0
F. HFD(config)# ip route 10.5.4.6 255.255.255.0 10.5.6.0
Ensurepass offers Latest 2013 640-802 Real Exam Questions , help you to pass exam 100%.