2013 Latest 350-029 Pass4sure Free Tests 281-290

Ensurepass

 

QUESTION 281

What are the differences between LLQ and CBWFQ? (Choose two.)

 

A.  LLQ priority queue bandwidth is policed with a congestion aware policer.

B.  With LLQ, bandwidth allocations for the priority queue and all the CBWFQ queues are configured using the priority command.

C.  LLQ does not support WFQ on the default traffic class (class-default).
D.  LLQ supports the addition of strict priority queuing.

E.  LLQ is configured using MQC and CBWFQ is configured using the fair-queue command.


Answer: AD

 

 

QUESTION 282

Which command will display the MPLS label binding for IP prefix 1.1.1.0 on the router?

 

A.  All of the above.

B.  show tag-switching tdp binding 1.1.1.0/24

C.  show tag-switching tdp bindings neighbor 1.1.1.0

D.  A and B both will show the binding.
E.  show tag-switching interface e0/0

 

Answer: B

 

 

QUESTION 283

Which of the following statements regarding Selective Packet Discard(SPD) is correct?

 

A.  Selective Packet Discard(SPD) is a mechanism to drop non-routing packets instead of routing packets when the process level queue is congested.

B.  Selective Packet Discard(SPD) is a mechanism to drop normal IP packets instead of VOIP packets when the link is overloaded

C.  None of above.

D.  Selective Packet Discard(SPD) is a mechanism to drop Frame Relay frames with the DE bit set instead of Frame Relay frames DE bits without being set when the link is overloaded

E.  Selective Packet Discard(SPD) is a mechanism to drop packets with low IP precedence instead of packets with high IP precedence when the link is overloaded

 

Answer: A

 

 

QUESTION 284

What is true regarding Autonomous Systems (AS )?

 

A.  All of the Above

B.  AS numbers are assigned by the IANA

C.  AS numbers are used by BGP (Border Gateway protocol ) to exchange IP routing information with neighboring AS

D.  In the internet, an Autonomous System (AS) is a collection of IP networks and routers under the control

 

Answer: A

 

 

QUESTION 285

If the OSPF protocol is used to connect customer edge (CE) routers to service provider edge (PE) routers in the VPN backbone, which two options best describe the use of SHAM links?

 

A.  A sham-link is created between any twoo VPN sites that belong to the same OSPF area and share an

OSPF backdoor link

B.  A sham-link is seen as an intra-area link between PE routers,an OSPF adjacency is created and database is exchanged

C.  A SHAM link is created between two directly connected PE routers so that it is preferred over the low speed backdoor door

D.  A SHAM link is part of OSPF network of MPLS-VPN provider.

 

Answer: AB

 

 

QUESTION 286


Assume two routers on the same subnet, R1 and R2, both configured for HSRP. R1 has a priority of 120. Which of the following HSRP interface configurations will always result in the R2 becoming the primary?

 

A.  standby 1 priority 120

B.  standby 1 priority 130 preempt

C.  standby 1 priority 130

D.  standby 1 priority 120 preempt
E.  standby 1 priority 110 preempt
F.  standby 1 priority 110

 

Answer: BC

 

 

QUESTION 287

If two routers, both reachable from one another, originate functionally equivalent type 2 external- LSAs (i.e, same destination, cost and non-zero forwarding address ), Which of the following statements would

apply ?

 

A.  Only the LSA generated by the lowest RID ASBR will exist in the network

B.  Two LSAs will exist in the network for this destination, but only the one generated by the highest RID ASBR will be used

C.  Two LSAs will exist in the network for this destination, and both will be used

D.  Only the LSA generated by the highest RID ASBR will exist in the network

 

Answer: D

 

 

QUESTION 288

What are BCP 38 (Best Common Practices 38)/RFC 2827 Ingress Packet Filtering Principles?

 

A.  Filter Smurf ICMP packets.

B.  Filter as close to the core as possible
C.  Filter as close to the edge as possible
D.  Filter as precisely as possible

E.  Filter both source and destination where possible.

 

Answer: CDE

 

 

QUESTION 289

Which of the following processes are likely to be found in a microkernel?

 

A.  Memory management
B.  Lightweight messaging
C.  Process scheduling

D.  Hardware abstraction

E.  Host stack

F.  All of the above

 

Answer: F

 

 

QUESTION 290

Using more than one label on a single packet is required in what context?

 

A.  MPLS TE

B.  When CEF switching and Label switching is done


C.  In all the above circumstances.
D.  MPLS VPN

 

Answer: D

 

DownloadLatest 2013 350-029 Pass4sure Free Tests , help you to pass exam 100%.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.